Kenmore Washer Hose Clamp WP285655 | Fix.com

Hose Clamp

&SeePartX&
11740613-1-S-Whirlpool-WP285655-Hose Clamp
11740613-2-S-Whirlpool-WP285655-Hose Clamp
11740613-3-S-Whirlpool-WP285655-Hose Clamp
https://www.fix.com/Schematics/Maytag/WH8VIOZB.gif
Click for the BBB Business Review of this Appliances - Small - Supplies & Parts in Dartmouth NS
Part Description:
This hose clamp is sold individually.
This part fixes the following symptoms: Leaking.
This part works with the following brands:
Part number cross reference:
This part works with the following products:
Washer, Washer Dryer Combo, Dishwasher, Refrigerator, Dryer, Ice Maker, Food Waste Disposer.

Installation Instructions

Showing 1-3 of 3 Instructions

The drain hose had a hole in it and needed to be replaced

Removed the lower front panel, disconnected the hose and replaced it with the new one, then replace the panel. The most dificult part was getting my old self on the floor and unscrewing the panel nuts.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Pump Hose , Check Drain Ball , Clamp , Hose Clamp , Hose Clamp
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Jacob from Center, TX

Leaking

Just with a nut driver to tighten the clamp

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Outer Tub to Pump Hose , Hose Clamp
Difficulty Level: Really Easy
Total Repair Time: Less than 15 mins
Tools: Nutdriver
Customer: greg from new martinsville, WV

Slight leak in tub drain hose

Unplug unit from electrical outlet. Remove two Phillips screws in bottom of front cover. Swing front cover up and off the washer. Loosen both hose clamps. Place a large rag (or several paper towels) around base of hose where it connects to the water pump. Gently loosen bottom of hose from water pump and remove. Gently loosen top of hose from tub drain and remove. Slide new hose top onto tub drain. Slip both new clamps onto hose (lower clamp screw should be on the inside of the hose so that there is no interference with rotating parts). Slide new hose bottom onto water pump. Tighten both clamps snuggly. Re-install front cover. Plug unit back in.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Outer Tub to Pump Hose , Hose Clamp
Difficulty Level: Really Easy
Total Repair Time: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: David from Middletown, PA
Showing 1-3 of 3 Instructions

Model Cross Reference List

This part works with the following models:

Fix Number: FIX11740613
Manufacturer Part Number: WP285655


Brand Model Number Description
Kenmore110088732791Washer Dryer Combo
Kenmore11010202000Washer
Kenmore11010202001Washer
Kenmore11010502990Washer
Kenmore11010502991Washer
Kenmore11010852990Washer
Kenmore11010852991Washer
Kenmore11012202100Washer
Kenmore11012502100Washer
Kenmore11012852100Washer
Kenmore11013202200Washer
Kenmore11013212200Washer
Kenmore11014102300Washer
Kenmore11014112300Washer
Kenmore11014202300Washer
Kenmore11014212200Washer
Kenmore11014222300Washer
Kenmore11014502300Washer
Kenmore11014852300Washer
Kenmore11015732400Washer
Kenmore11015842400Washer - Kenmore Washing Machine
Kenmore11015852400Washer
Kenmore11015862400Washer
Kenmore11015864400Washer
Kenmore11015942400Washer
Kenmore11015942401Washer
Kenmore11015944400Washer
Kenmore11015944401Washer
Kenmore11015952400Washer
Kenmore11015952401Washer