Coffee Maker Seals and Gaskets

Fix Number

FIX10311182

Manufacturer Part Number

5332149100

This generator gasket is an OEM quality part that is used to seal the filter to the generator of your coffee maker. If this part is cracked, torn, stretched, or otherwise damaged, it should be replaced. It is made of silicone, is orange in color, has an outside diameter of 43.6mm, inside diameter of 35.2mm, and a thickness of 4.2mm (these measurements are approximate). Sold separately.

Fix Number

FIX10310752

Manufacturer Part Number

5313217701

This is a single O-ring for a coffeemaker/espresso machine. It measures approximately 5/16-inches in outer diameter and has a 3/16-inch inner diameter. This O-ring attaches to the tube, which is connected to the upper boiler. It acts as a water-tight seal to prevent liquid from leaking between these two connected parts. Due to the high temperature and wet conditions, this rubber O-ring is subject to wear and may require replacement.

Fix Number

FIX17585748

Manufacturer Part Number

SP0021707

This ring and seal assembly ensures even water distribution through the brewing head while preventing leaks around the interface. Wear may result in dripping, uneven extraction, or pressure loss. Replacement restores proper dispersion and consistent beverage quality.

Fix Number

FIX10310753

Manufacturer Part Number

5313217751

This is one black rubber O-ring for coffee makers and espresso machines. This O-ring is compatible with various products, however serves the same function. It creates a seal to keep liquids from leaking from the appliance. If your appliance begins to leak, you will want to inspect this O-ring for cracks or breakage.

Fix Number

FIX10310754

Manufacturer Part Number

5313217761

Genuine Delonghi replacement part, this item is sold individually. This o-ring is attached various parts of the Delonghi products shown below. Its purpose is create a seal to keep liquid from leaking from the machine. Over a period of time o-rings will become brittle or stretch.

Fix Number

FIX12020061

Manufacturer Part Number

7313285849

This is a genuine Delonghi product. This Gasket is used on many models of Delonghi espresso makers. The Gasket is made of a high temp silicone and is used to create a seal between the diffuser and the filters. If water, steam, or coffee leaks out of the filter while brewing then this part should be replaced. To replace this Gasket first remove the diffuser by removing the screw. Then, gently pull the old gasket off. Clean the area with a damp cloth. Install the new Gasket and reinstall the diffuser.

Fix Number

FIX12008388

Manufacturer Part Number

SP0002502

This is a genuine manufacturer-sourced replacement part which is specially produced for Breville equipment. It helps to distribute the pressure evenly and provide a tight seal between connected parts, over time it may wear out and begin to fail eventually requiring a replacement. Keep in mind this high-quality item is made of durable rubber material and is sold individually.

Fix Number

FIX10310766

Manufacturer Part Number

5313220031

This part comes directly from Delonghi. This O-Ring is used in multiple models of Delonghi coffee makers. The O-Ring is made from a high temp silicone. This O-Ring is used to seal steam, water, and frothed milk depending on the model it is installed in. The O-Ring should be replaced if it no longer holds a good seal due to cracks, tears, or becomes hardened. Caution should be taken to not over stretch the gasket when installing it.

Fix Number

FIX10401820

Manufacturer Part Number

MS-0698568

It is an OEM item which is made for use with Krups espresso makers. This component provides an air-tight seal for the piston. Over time the material will wear out and it may begin to crack eventually requiring a replacement to ensure the unit functions properly. To ensure the correct installation of the new part, refer to the specific diagrams of your model. It is a high-quality seal which is made of durable rubber material and is sold as an individual component. You will need a screwdriver to take the housing apart when performing this repair.

Fix Number

FIX10404338

Manufacturer Part Number

MS-5015004

This is a genuine replacement part that is supplied by the original equipment manufacturer, it is specially designed for Krups espresso makers. It is one of the special seals for the rod, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. This high-quality component is made of durable rubber material and is sold individually.