Jenn-Air Ice Maker Parts

Jenn-Air Appliance Parts

Popular Jenn-Air Ice Maker Parts

Refrigerator Water Filter
$75.74
In Stock
Fix Number
FIX8759230
Manufacturer Part Number
F2WC9I1
This genuine OEM replacement part is a water filter for your fridge or freestanding ice maker. The filter is used to remove contaminants and particles from the water, to ensure a clean and fresh taste. The filter should be replaced every six to nine months, or after 2000 gallons of water have passed through, whichever occurs first.

Installation Instructions

Shirley C from Houston, TX
Replace water filter
Just followed the directions. Read more...
Ice Maker Bin Temperature Sensor
$73.78
In Stock
Fix Number
FIX11755842
Manufacturer Part Number
WPW10511923
This bin temperature sensor is for ice makers. The bin temperature sensor monitors the temperature in the ice maker bin and sends the temperature reading to the electronic control board. Disconnect the power before installing this part. Wear work gloves to protect your hands.
★★★★★
★★★★★
2 Reviews
Fix Number
FIX1957416
Manufacturer Part Number
W10124096
This condenser fan motor kit is used in icemakers and freezers, the purpose is to circulate air through the condenser in the compressor area in order to keep it cool. If your fridge is making loud noises when running or it is getting too warm, then consider replacing this part to solve your problem. The tools needed for this repair: 1/4 inch nut driver, slip joint pliers, 1/4 inch drive ratchet, and small flat blade screw driver. For installation instructions, follow manual provided by the manufacturer. Unplug tool from power source before you begin installation process.
Fixes these symptoms
  • Clicking sound
  • Freezer section too warm
  • Fridge and Freezer are too warm
  • See more...

Installation Instructions

Patricia from Moline, IL
Very noisy whenever the fan came on.
Watched several online videos. Removed the fan blade, then the motor still attached to the motor mount so I could see what I was doing to attach the new motor to the motor mount. Then reinstalled the whole assembly, plugged in it's wires with the supplied adapter and attached the new fan blade. Read more...
PUMP
$67.97
In Stock
Fix Number
FIX16730541
Manufacturer Part Number
W11566405
Used with stand-alone ice cube makers.

Installation Instructions

Robert from China Grove, NC
No ice
Board diagnostics stop at Cir pump. Replaced circulation pump. Made half of one cycle of ice. Stopped. Replaced control board. Problem solved. But, set thermosensor too low on bin wall. Made one cycle of ice and stopped. Set thermosensor higher on bin wall, just above the front threshold of the bin, now all is working great. Control circuit board swap was easy except for the 2 rear screws that hold the control panel case to the bin. The holes for these screws are not visible without a mirror and are tricky to start. Read more...
PUMP
$142.41
In Stock
Fix Number
FIX16555297
Manufacturer Part Number
W11542867
PUMP
$65.84
In Stock
Fix Number
FIX16555298
Manufacturer Part Number
W11542868

Installation Instructions

Vernon from Halethorpe, MD
Light swithch stop working had to be replaced.
Use a flat head screw drive to pry the old switch out, remove the 2 wires and connected them to the new switch and pop the new switch back in done in 5 minutes tops. Read more...
SWITCH
$28.80
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12584655
Manufacturer Part Number
W11291138
This is a light switch for your refrigerator. It activates when the door of your appliance is opened, and it will turn the light inside on and off. You will need to replace this part is if your light is not working properly. In order to make this repair you will need a Phillips screwdriver, a pair of needle nose pliers, and a small flat blade screwdriver. This light switch is almost 2 inches long, 1.5 inches wide, and just over an inch thick.
Fixes these symptoms
Water Inlet Valve
$145.30
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11765823
Manufacturer Part Number
W10897719
Ice Cutter Grid Complete Assembly
$273.21
In Stock
Fix Number
FIX11740334
Manufacturer Part Number
WP2313637
This is an ice cutter grid assembly for your ice maker. If your machine is not producing ice properly, the assembly may need replacing. You will find this part in the main unit of the ice maker. The thin heated wires slice the ice into small cubes that are released into the bin. If your cutter is damaged the ice will clog up your appliance.

Installation Instructions

John from Bakersfield, CA
Cutter grid not heating up
It was an easy fix for a guy with absolutely ZERO appliance repair experience. I used a nut driver to unscrew two screws that were on each side of the front of the grid. There were two easy to reach electrical harnesses to unfasten, as well. The grid easily slid out and I had no problems inserting and securing the new grid. Just be very carful when handling the new grid as I'm sure the thin grid wires could easily be broken. Read more...
PAN-WATER
$28.14
In Stock
Fix Number
FIX16744957
Manufacturer Part Number
W11614100

Installation Instructions

Brian from St. Louis, MO
Replacing the original water inlet valve with the replacement
While the repair itself is simple, several things complicated it. First off, the valve did not come with any instructions at all. While I am no novice with appliance repairs, I had not run into the new quick plumbing connections before, so I had to look up info on the internet to make sure I was doing it right. The next problem is that the orientation of the valve is not the same, so the water inlet now comes in on the bottom, instead of from the top. Since mine had originally been done in copper tubing, I had to redo this piping as there was not enough to go. First trip to the hardware store to buy a flair connector to add a bit of tubing (which I happened to have). Once the inlet piping was done, I discover that the outlet piping connection is a completely different size on the new valve. The old valve had 1/4" on both connections, the new one has 1/4" inlet and 5/16" out. Kind of stupid, but that's what it is. Second trip to the hardware store to get a 1/4 X 5/16th compression fitting and some 5/16" plastic tubing, which is only sold in 10' lengths. So my "exact replacement" took two hours, counting hardware store trips, and an extra $15 worth of parts to make it work. It works great so far, but I'm not to happy. The electric and mounting brackets did match up exactly, so no problems there. Read more...

Jenn-Air Ice Maker Appliance Types

Related Jenn-Air Ice Maker Parts

Popular Jenn-Air Ice Maker Models