OEM Frigidaire Range Infinite Burner Switch [316436001] | Ships Today | Fix.com
https://fixcom.azureedge.net/Schematics/Frigidaire/9OOZSWQ0.gif
See part 54A in the diagram
https://fixcom.azureedge.net/Schematics/Frigidaire/9OOZSWQ0.gif

Infinite Burner Switch

Your Price
$24.58

Fix Number: FIX1145040

Manufacturer #: 316436001

Manufactured by: Frigidaire

Get this part fast. Average delivery time via standard shipping: 1.8 days.

Part description

This switch controls the stove top 8" surface burner.

Works with the following brands

Frigidaire, Kenmore, Tappan, Crosley, Gibson, Westinghouse, Kelvinator, Uni, Electrolux

Works with the following products

Range

Fixes the following symptoms

Element will not heat | Oven is too hot | Will Not Start | Will not program

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part Photo
Description
Price
Availability
Part Number: FIX1145039
This switch controls the stove top surface burner.
$35.37
In Stock
Order within the next 11 hrs and your part ships today!

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 4.4 / 5.0, 18 reviews
>
<
Customer:
Dan from RICEBORO, GA
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
8" burner on stove would go to high heat even if set on low.
Pulled stove out.
Disconnected plug.
Removed back upper cover (6 screws).
Removed upper and lower wiring harness (quite easy).
Removed burner knob (on front of stove), removed two screws holding infinite switch.
Removed old switch, replaced with new.
Replaced screws at front.
Replaced burner knob.
Reinstalled back plate, plug in, good to go.
1 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
CONNIE from WYTHEVILLE, VA
Parts Used:
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Bottom bake element burned out and my 8 inch stove eye would get stuck on high heat.
I flipped the breaker to my range then unplugged it from the wall. I removed my oven door and bake racks for easy access. Bake element was as easy as removing two screws, unplugged 2 wires and removed the old element. Attached wires and screws to the new element, slid the bake racks back in and attached the oven door. Since I had to repair the Infinite Burner Switch I left the range unplugged until that project was finished. I removed 5 screws from the top back plate covering the Burner switches. Gently pulled the knob off the front of the range. Removed the 2 screws from the Burner switch and went to the back for the repair. I pulled out my new Burner switch to compare with the old piece and found that my new replacement part looked different from the old part. I did call for help because there was a huge difference in appearance. I was given a phone number to call because the part number was coming up to be the right product for my Model number. I called the manufacture and was told that it was the right part to which I asked if it was a replacement for the original part since mine looked different. It indeed was a replacement but they couldn't tell me how to hook it up so they gave me another number to call. This was a service center and they couldn't advise me on the proper hookup. Now mind you the old Switch has codes like H1, H2, P and so on, so I was thinking that all I had to do was look for the same codes on the replacement part and place each wire that I removed from to old to the new being mindful to attach to the same code. This is where I chickened out and let my husband do that ....just in case.....lol. After placing all wires to the new part, I attached it back to the range with the two screws and pushed the knob back on. Husband attached the back plate with the 5 screws, plugged range back up and turned the breaker back on. We are now cooking as if we had a new range! My advice is don't be afraid to TRY!!!!!! Saved my family a huge repair bill.
1 of 2 people found these instructions helpful

Were these instructions helpful?   

Customer:
Larry from Norwich, OH
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Large burner had no control just red hot.
It was so easy just like your video showed.Thanks for the help.
1 of 2 people found these instructions helpful

Were these instructions helpful?   

Customer:
Long from Creedmoor, NC
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Burner did not heat up
I troubleshot and found the burner switch output pin burned out/or broke. It took me 15 minutes to replaced the burner switch. very easy to replace. if any one has problem with his/her rang, do not throw your rang away. find out what's wrong with it and repair yourself..
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
CHARLES from LENOIR, NC
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
When burner turned down from high to simmer, remained at high.
Removed back panel . removed knob and switch. connected new switch. reinstalled switch, knob and back panel. Burned worked fine.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
hon from cordova, TN
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
The new part is bigger than the old part, not exactly the same shape .
The new switch has the same terminal mark like L1,P1,L2 etc. The terminals are not at the same location of the switch as the original one. However, I just removed and reconnected the wires in accordance with the terminal marks and it worked perfectly. I saw the same manufacturer name in the old and new switch and this gave me the confidence that it will work.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
heather from portland, OR
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
Rear 8 inch burner wouldn't heat up
Unplugged the stove from the wall, from the back of stove removed the 3 screws holding the upper cover of stove to access the infinite burner switch. Took a pair of pliers and simply removed the five electric connectors from old switch and replaced them on the new switch. There were 5 in all. I let the part hang with all the new connectors attached. I removed the 2 screws holding the old switch to the stove. removed old switch and screwed the new switch in. replaced knob,back plate and plugged the oven back in. Easy repair would have cost bunches to hire someone else. It took 15 minutes tops! BTW I have never worked on a stove before! Yes it was a success!
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Michelle from Piedmont, SC
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Cooktop element wouldn't turn off, needed switch. Bake element dissolved when cooking, needed new
The switch was very easy. Just a few screws to take out of the rear panel, then pull the wires off the old and put n new. I did them one at I time so I wouldn't have to keep track. Recommend bright light or flashlight, the imprint for which connector it is is really hard to read. Works same as original, it's just laid out differently so you need to look at the label (P, L1, etc) before you move the wire. If it doesn't work right away, look at the other switch of the same size that works to make sure you got the right wire on the right prong (I initially used the wrong one, the letter I could read but the 1 and 2 are tiny). Works great now.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Timothy from Lehigh Acres, FL
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Heating element was intermittently over heating and switch was sparking
Followed the repair instructions at each of the parts web pages. Also found that the instructions at this location were helpful to understand why the new switch did not look like the original switch.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
George from Onalaska, TX
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Burner would not shut off.
Front left burner would come on and not shut off or stay on high. I replaced the switch behind the control knob. Go by the lettering and numbers on the new switch, and not the location of the connecting wires of the old switch. The location of the wires on the new switch are different from the original and the after market is a different and much better switch. You Tube has good instructions, but the details are not sufficient. Label the leads going to the old switch. I used scotch tape and labeled L1 H2 ect. Use a screw driver to pry the old connectors off . Put the wires on the new switch using the old numbers as a guide (no matter the location on the new switch). So L1 goes on L and so on. After all wires are inserted and the switch is screwed into the front panel plug in the stove to see if there are any conflicts. Try it before you move it back into place.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
John from Aransas Pass, TX
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
8' burner had no heat adjustment-only high heat
Followed the video instructions.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
William c. from Sycamore, IL
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Burner cracking when turned on!
Unpluged electric cord took of back top panel! Then found switch wires not on turminals all the way. but replaced the switch anaway.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
jacob from Southern Pines, NC
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
Power to the switch but no power to the burner as determined by circuit tester.
turned off breaker and checked with circuit tester to make sure no electricity getting to range. took off back access panel of range with impact driver. used pliers to remove one wire at a time off faulty switch and plugged in to new switch. removed faulty switch by removing two screws from front side of switch with impact driver. fastened new switch in place using same two screws. turned breaker back on and burner worked perfectly.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Gentry from Wise, VA
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Front bunner quit working
the part was an exact fit , but, it was the connector combo that had fried onto the part. I had to replace the connectors with insulated spades. this was not included in the how to instructions on line, but I"d done this before. just a heads up on how to it was not hard at all and I'am a very happy customer.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Micheal from Lancaster, PA
Parts Used:
  • Infinite Burner Switch
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Burner overheating
Pop out a few screws from behind the control panel and match the quick connects from the old switch. Try not to pull the quick connect out of the light indicator.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

>
<

Model Cross Reference

This part works with the following models:

Fix Number: FIX1145040
Manufacturer Part Number: 316436001
Brand
Model Number
Description
Tappan
31-2232-00-01
Range - Free Standing, Electric
Tappan
31-2232-00-02
Range - Free Standing, Electric
Tappan
31-2232-00-03
Range - Free Standing, Electric
Tappan
31-2232-23-01
Range - Electric
Tappan
31-2232-23-02
Range - Free Standing, Electric
Tappan
31-2232-23-03
Range - Free Standing, Electric
Tappan
31-2442-00-01
Range - Electric
Tappan
31-2442-00-02
Range - Electric
Tappan
31-2442-23-01
Range - Electric
Tappan
31-2442-23-02
Range - Electric
Tappan
31-2452-00-01
Range - Electric
Tappan
31-2752-00-01
Range - Free Standing, Electric
Tappan
31-2752-00-02
Range - Free Standing, Electric
Tappan
31-2752-00-03
Range - Free Standing, Electric
Tappan
31-2752-23-01
Range - Free Standing, Electric
Tappan
31-2752-23-02
Range - Free Standing, Electric
Tappan
31-2752-23-03
Range - Free Standing, Electric
Tappan
31-2852-00-01
Range - Electric
Tappan
31-2852-00-02
Range - Electric
Tappan
31-2852-00-03
Range - Electric
Tappan
31-2852-23-01
Range - Electric
Tappan
31-2852-23-02
Range - Electric
Tappan
31-2852-23-03
Range - Electric
Tappan
31-2862-00-01
Range - Electric
Tappan
31-2862-00-02
Range - Electric
Tappan
31-2872-23-01
Range - Electric
Tappan
31-2872-23-02
Range - Electric
Tappan
31-2872-23-03
Range - Electric
Tappan
31-3342-00-01
Range - Free Standing, Electric
Tappan
31-3342-00-02
Range - Free Standing, Electric