Porter Cable Table Saw Parts

Fix Number

FIX10169670

Manufacturer Part Number

330015-03

This hex nut with internal threads, screws to the shank of a bolt or a hex cap screw in a variety of lawn and gardening tools. It can have multiple applications depending on the tool you are using. To replace, you will need a wrench to loosen and tighten the nut. For detailed installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug tool from power source before beginning this repair project.

Fix Number

FIX18982779

Manufacturer Part Number

5140158-17

Fix Number

FIX18982900

Manufacturer Part Number

5140160-29

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Porter Cable equipment. The purpose of this dado throat plate is to reduce splintering and chip-outs on the cuts, it also prevents thin slices of wood from jamming in between the blade and the plate during a cut. This high-quality part is made of durable material and is sold individually, keep in mind the hardware to secure it is sold individually.

Fix Number

FIX18982312

Manufacturer Part Number

5140113-88

This cord is an authentic Porter Cable replacement part and is sold individually. It is made with tough, thick rubber insulation for a long service life. rnPower Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Fix Number

FIX18981419

Manufacturer Part Number

488871-00

This genuine manufacturer-sourced screw is made for Delta, Black and Decker and Porter Cable equipment. The nut is a standard hardware which may have multiple applications. Check the diagrams for your specific model to ensure the exact location and use of this part. It is an identical replacement for a missing or a damaged hardware that was installed on a new unit. One durable metal nut is included. A wrench will be needed to secure or remove it.

Fix Number

FIX12021560

Manufacturer Part Number

1348266

This is an OEM replacement carbon brush, sold individually. To ensure your motor is running smoothly and efficiently, it is advised to inspect the carbon brushes every few months, as they are prone to regular wear. The carbon brush has an important job of conducting electrical current, so if worn, your tool will not function as it should. If your tool is smoking or burn marks are present, it is advisable to also check the condition of the armature, as this could indicate more serious motor problems.

Fix Number

FIX18981975

Manufacturer Part Number

5140082-09

This is a single bevel gear soured directly from the original manufacturer. The bevel gear is part of the assembly responsible for raising and lowering the blade on the saw. It mates with another identical bevel gear (sold separately). The bevel gear is connected to the height adjustment bolt and then the hand wheel assembly. The second bevel gear is attached to the height worm. They are attached by two hex head screws.

Fix Number

FIX18982213

Manufacturer Part Number

5140096-02

This is a genuine Porter Cable replacement part that is OEM sourced to ensure a high level of quality. This item is intended to be used with table saws. The durable plastic handle attaches to the front of the rip fence. This item is used to actuate the fence lock assembly when changing the position of the fence. The handle is sold as an individual replacement part.

Fix Number

FIX10169676

Manufacturer Part Number

330016-01

This is an original Delta replacement part. The washer is designed by the manufacturer for use in power tools such as table saws, miter saws, and routers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different washers used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You may require a screwdriver when replacing this item. This part is sold individually. Included in part number 395930-01

Fix Number

FIX10315907

Manufacturer Part Number

1310311

This item is available as an individual replacement part. The roll pin attaches to the guard and is made of metal. If this item becomes bent or broken it will need to be replaced and may require a set of pliers during the installation. This is an OEM part directly sourced from the manufacturer for use in saws, drills, jointers, and sanders made by Delta, Porter Cable, and Black & Decker.