Makita Table Saw Parts

Fix Number

FIX10153852

Manufacturer Part Number

664463-0

This power cord includes 2 prongs, 2 wires, and the gauge is 14. The measurement is 8 feet long and the type is bare wire. The cord is used on various power tools, specifically gardening and lawn equipment. With use and time, power tool cords can become frayed. If there are visible signs of wear on your cord, it is important to replace it immediately. For safety practices and installation instructions, refer to the diagram provided by the manufacturer.

Fix Number

FIX10155934

Manufacturer Part Number

951116-3

It is a genuine item that is supplied by the original equipment manufacturer for use with Makita saws and sanders. This is a standard hardware which may have multiple applications depending on the model of your tool. Refer to the appropriate diagrams for your model to ensure the exact location and the correct use of this part. It is made of durable metal and is sold individually. You may need pliers to replace this spring pin.

Fix Number

FIX10144692

Manufacturer Part Number

257060-5

This ring (15.8) is supplied directly from the original equipment manufacturer. The metal ring is designed to help secure the blade in the various miter saw devices. A screwdriver and a wrench are often necessary for the removal and replacement. The ring is sold individually.

Fix Number

FIX10150187

Manufacturer Part Number

416333-7

This is an authentic Makita part that has been OEM sourced to ensure a high level of quality. The metal rack plate attaches to the plate under the table and is used to allow the blade case to move side to side when making bevel cuts. The rack plate is priced as a single item, please see your model's diagram for related parts.

Fix Number

FIX10145980

Manufacturer Part Number

271073-2

It is a genuine OEM sourced part which is specifically designed for use with Makita table saws. The handle goes between the arm and the handle shaft. Keep in mind this high-quality part is made of plastic and is sold individually. A screwdriver may be necessary during the installation of this part. This item may become broken and will need to be replaced.

Fix Number

FIX10145367

Manufacturer Part Number

266035-3

This is a genuine OEM sourced replacement part which is specially designed for use with Makita equipment. It is a standard hardware which has multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality item is made of durable metal and is sold individually.

Fix Number

FIX10142391

Manufacturer Part Number

224333-1

This is an original OEM part. The Makita flange 53 is made of metal, and is compatible with several saw devices. This part is fastened between the hex. flange head bolt and the ring 15.8, and assists in securing the TCT saw blade. Please refer to manual and diagrams for specific instructions. This item is sold individually. A wrench and a screwdriver are helpful in making the repair.

Fix Number

FIX10156641

Manufacturer Part Number

CB154

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric braking power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

Fix Number

FIX10146236

Manufacturer Part Number

286212-1

This is an Authentic Manufacturer Approved replacement part used on Miter Saws. This item is made out of Rubber and it is Sold Individually. This part fits in the Base and it provides cushion for the unit. No tools are required to replace, simply push it in the opening of the base.

Fix Number

FIX10153647

Manufacturer Part Number

651567-7

This switch has 5 terminals an a safety lock system that prevents accidentally turning it on. This is a genuine Makita replacement part. Switches are commonly replaced parts in tools. A switch handles on/off and variable speed operations. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because switches use mechanical internals, they will degrade and wear out over time, eventually needing replacement. Some common signs of a broken or failing switch are as follows: • The tool has completely stopped functioning - it will not start. • The tool operates intermittently, requiring multiple tries to turn on, until eventually it won't start at all. • The variable speed function and electric braking aren't working properly.