OEM Jet Table Saw Parts & Accessories

Tire

$40.28

Fix Number: FIX10375821
Manufacturer Part Number: 100025A

This manufacturer-approved tire is for band saws. Tire covers the wheel on which the blade rotates. The tire is a tight fit; stretch it around the wheel. Unplug the saw before installing this part. Wear work gloves to protect your hands.

Installation Instructions

Thomas from GROESBECK, TX

Tires were 14 years old and were getting rough

Step 1: Unplug band saw
Step 2: Remove Blade
Step 3: Use awl to pry up one edge of old tire, hold it up with your thumb and push the awl the rest of the way through, and pry the old tire off. (be careful not to mare the aluminum wheel with the awl.)
Step 4: Clamp the tire in one spot to the wheel, insert the tire until it will not go on anymore, clamp it at the point, work the tire on with both hands from that point until it is on the wheel, remove clamps, and seat the tire on the wheel. (use clamps that have padded covers where they touch the wheel, again making sure not the mare the wheel.
Step 5: Repeat Steps 3 and 4 for the other wheel.
Step 6: Re-install blade and set tracking and make coplanar adjustments. (hand rotate while setting tracking)
Step 7: Plug the band saw in
Step 8: Start the band saw and make sure it runs true. (It will run quieter as well)
Step 9: Have a nice day. Read more...

Tire

$68.37

Fix Number: FIX10391908
Manufacturer Part Number: JWBS18DX-133

This genuine OEM supplied component is specially made for use with Jet and Powermatic band saws. Its purpose is to help track the blade on the wheel. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement to ensure best performance. Keep in mind this high-quality tire is made of durable rubber and is sold individually. Please make sure to refer to the owners manual of your model for the correct application of this part.

Ball Bearing

$40.28

Fix Number: FIX10463888
Manufacturer Part Number: BB-6203ZZ

This ball bearing is 17 mm and fits a variety of gardening power tools. The ball bearing has two contact rubber seals on each side and two non-contact metal shields on each end as well. Tip: if your tools needs only one seal or shield, then take off one of the shields or seals from this ball bearing. Refer to the manual provided by the manufacturer for further installation instructions and a detailed diagram.

Installation Instructions

Adam from FREMONT, NE

Saw was making loud screeching noise and unsatisfactory cuts

1: disconnect power and remove blade
2: remove spanner nut
3: remove arbor nut. Spins opposite:
righty loosy lefty tighty
4: remove arbor with mallet and dowel
5: use arbor press to take off ball bearing
6: press on new bearing Read more...

Eccentric Shaft

$6.09

Fix Number: FIX10467150
Manufacturer Part Number: PWBS14-240

Table Insert

$14.64

Fix Number: FIX10391986
Manufacturer Part Number: JWBS20-144

Installation Instructions

William from COUNCIL BLFS, IA

Upper bearing bracket broke and throat plate was damaged

Took the old parts off and put the new ones on Read more...

Watch the install video

TABLE INSERT WBS-14CS/OS

$20.75

Fix Number: FIX10376942
Manufacturer Part Number: 199037

On/Off Switch

$45.17

★★★★★

1 Review

Fix Number: FIX10382826
Manufacturer Part Number: 994534

Ball Bearing 608Zz

$36.62

Fix Number: FIX10383284
Manufacturer Part Number: BB-608ZZ

This is a ball bearing for various power tools. It distributes weight evenly and reduces friction between parts of your tool. Depending on how often you use your tool, the ball bearings are subject to a lot of pressure and can easily malfunction. Because this part will reduce wear on your tool and help it run smoothly, we recommend replacing it when you notice any damage.

Watch the install video