OEM Porter Cable Reciprocating Saw Parts & Accessories

Ball Bearing

$9.13

Fix Number: FIX10180907
Manufacturer Part Number: 605040-15

Genuine OEM sourced replacement part used on a variety of power tools. Ball bearings are used to reduce friction between rotating parts. Bearings experience constant wear when the tool is in operation, because of this they need to be periodically checked and replaced if needed. This part is made out of metal and it is sold individually. Included in part number 381004-00 spindle assembly.

SS/A-SHOE ASSEMBLY

$29.37

Fix Number: FIX12507414
Manufacturer Part Number: 911450SV

Genuine OEM replacement part, this part is sold individually. This part is used on all of the saws shown below. The purpose of the Shoe Assembly is to press it to the material being cut to make a better cut and less vibration to the user. It can be adjusted for different length of blades, it also pivots for angle cuts. It is advised to always use this part. Otherwise you could cause damage to the saw.

STRAIN RELIEVER

$12.08

★★★★★

1 Review

Fix Number: FIX12499955
Manufacturer Part Number: 901266

This is a strain reliever for your power tools. It found at the meeting place between your cord, and the outer tool housing. The relief is an important part for your power tool because it protects your cord from tearing and breaking due to constant pressure. Keep your relief in good condition because it will extend the life of the cord, and the machine overall.

Installation Instructions

Jeff from WISC RAPIDS, WI

Strain reliever broken at base of saw. Core frayed.

1. Unplug saw. 2.Examine and determine which parts need to be removed to gain access to switch. 3.Remove screws one at a time and placed in dish keeping track of size and length of where removed from handle. 4. Slowly pull handle apart exposing switch and wires. 5. Remove screws holding black and white wires keeping track of which wire goes where. 6. Thread new power cord the same way the old one was positioned though the handle and reassemble. Read more...

BRUSH & RETAINER ASY

$16.77

Fix Number: FIX12504955
Manufacturer Part Number: 874289

Genuine Porter Cable replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

BALL BEARING

$11.07

Fix Number: FIX12497015
Manufacturer Part Number: 874538SV

This is a genuine OEM replacement part, it is sold individually. This Ball Bearing is sealed on both sides. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. • This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

$6.51

Fix Number: FIX18988346
Manufacturer Part Number: 90556466

RETAINING RING

$6.51

Fix Number: FIX12464070
Manufacturer Part Number: 684179

This is an authentic OEM part which is designed for use with Porter Cable, DeWalt and Black and Decker saws. It is a standard hardware which helps to secure a component on a shaft. This is an identical replacement for a damaged or a faulty part that was installed on a new unit. Check the appropriate diagrams for your model for the exact location and the correct installation of this retaining ring. It is best to use snap-ring pliers to remove the old part and secure the new one. One durable metal retaining ring is included.

Watch the install video

Electric Drill Cord Protector

$10.75

Fix Number: FIX10169655
Manufacturer Part Number: 330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

Cord Set

$16.31

Fix Number: FIX10115196
Manufacturer Part Number: A10193

This cord is a genuine Porter Cable replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. rnPower Cord Specifications: rn • 2 Prongs rn • 2 Wires rn • 16 Gauge rn • 10 Feet Long

Ball

$6.51

Fix Number: FIX10165151
Manufacturer Part Number: 000903-00

This connecting ball is an authentic manufacturer replacement part used in various power tools. It is a stainless-steel ball that provides a pivot point that allows the attached components to move back and forth smoothly during use. If the connecting ball falls off or becomes loose, worn out, or damaged, the equipment will become unstable or unable to move at all.

Porter Cable Reciprocating Saw Parts

Popular Porter Cable Reciprocating Saw Parts

Installation Instructions

Installation Instructions

Porter Cable Reciprocating Saw Appliance Types

Related Porter Cable Reciprocating Saw Parts

Popular Porter Cable Reciprocating Saw Models

Porter Cable Reciprocating Saw Parts

Start With Your Model Number

Popular Porter Cable Reciprocating Saw Parts

Installation Instructions

Installation Instructions

Porter Cable Reciprocating Saw Appliance Types

Related Porter Cable Reciprocating Saw Parts

Popular Porter Cable Reciprocating Saw Models