Makita Chop Saw Parts

Fix Number

FIX10138861

Manufacturer Part Number

125919-3

This replacement starter assembly is specially manufactured for Makita handheld cut-off saws. It is a genuine item that is sourced from original equipment producer. This is the starter assembly that allows user to pull-start the engine. This assembly includes a plastic housing, starter pulley, recoil spring, grip and the pull rope. Please note the hardware to secure this part is sold separately. You will need a hex key or an allen wrench to complete this repair.

Fix Number

FIX10149734

Manufacturer Part Number

411478-6

This is a single authentic switch activator button. Miter saws have a lockout mechanism on the switch, which stops the tool from being turned on by accident. The lockout is released by pushing on the switch button. The switch button can sometimes break or get lost and will need to be replaced. This is a very easy repair that does not require any tools. The switch button is secured with a plastic locking tab and can be removed by pulling it from the housing. To install the new switch activator button, position it in the housing and press it down until you hear a click.

★★★★★

★★★★★

1 Review

Fix Number

FIX10156666

Manufacturer Part Number

CB458

This part includes two OEM carbon brushes with the wire leads attached. Your tools motor requires two carbon brushes to create electricity for the armature. It is common for the carbon brushes to wear down over time, and this is why it is important to continually inspect them and replace them as part of your regular maintenance. If you notice sparks around the commutator, this may indicate a worn brush or a damaged armature, so we recommend inspecting both. To access this part you will need to remove the rear cover.

Fix Number

FIX10153567

Manufacturer Part Number

651131-4

This replacement switch is a genuine item sourced directly from manufacturer. It is an important item that handles on and off function of a unit, allowing user to control the tool. Switches have moving mechanical parts. These parts will eventually break down and fail requiring replacement. Please note the switch is sold individually. Replacing this item is a simple task that should only require a screwdriver. • Remove the housing screws • Remove housing/cover • Disconnect wires from the old switch • Replace old switch with a new one • Reconnect wires • Reassemble and test the unit

Fix Number

FIX10144692

Manufacturer Part Number

257060-5

This ring (15.8) is supplied directly from the original equipment manufacturer. The metal ring is designed to help secure the blade in the various miter saw devices. A screwdriver and a wrench are often necessary for the removal and replacement. The ring is sold individually.

Fix Number

FIX10140693

Manufacturer Part Number

166106-5

This part is supplied directly from the original manufacturer. It is specially designed for use with Makita handheld cut-off saws. The purpose of the dust bag is to collect dust from the unit. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement. Keep in mind this high-quality component is made of durable material and is sold individually. Check the owners manual for your model for the correct installation of this part.

Fix Number

FIX10153356

Manufacturer Part Number

643700-5

This is a manufacturer sourced replacement part designed for use with Makita power tools. It helps to secure the brush in the housing. This screw-in cap is made of hard plastic and it is sold individually and measures 7-18 HM 1500. To replace it you would need a flat-head screwdriver.

Fix Number

FIX10156645

Manufacturer Part Number

CB203

This part includes two carbon brushes with the wire leads and brush springs attached. In order for your motor to run at peak performance, it is imperative that the carbon brushes are well-maintained. The carbon brushes are needed to conduct electricity to the armature through the commutator. Over time these brushes wear down due to the constant rubbing. They should be regularly inspected to ensure your equipment continues to run smoothly. This repair should only take a few minutes.

Fix Number

FIX10153680

Manufacturer Part Number

651922-3

This replacement switch is specially made for use on Makita power tools. Switches are a commonly replaced item in power tools. They play a key role by controlling on/off function of a tool. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. To replace this switch you would need a screwdriver. • First make sure the tools is not plugged in • Remove housing screws • Disconnect wires from the old switch • Remove it from the housing • Place the new switch in the housing • Reconnect wires to it • Reassemble and test the unit

Fix Number

FIX10141724

Manufacturer Part Number

213021-5

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.