Porter Cable Belt or Drum Sander Parts

Fix Number

FIX12467035

Manufacturer Part Number

A03070

This is a Genuine OEM Sourced replacement part designed for use with Sanders and Band Saws. This item is made out of Plastic and it is Sold Individually. It includes Two (2) Pieces of the Knob. Please note the Screw used to secure this Knob is Sold Separately.

Fix Number

FIX12511677

Manufacturer Part Number

908910

This is a shoe assembly, which includes the steel shoe with a corked platen, and the three screws needed to attach it to the sander. This OEM part is a direct replacement for the original. The shoe assembly is the surface that the sandpaper belt will run against. Over time, the shoe will eventually wear out due to its consistent contact with the sandpaper belt. When it wears out this can cause irregular sanding to occur. For this simple repair, you will remove the sanding belt, and then unfasten the three screws securing it to the sander. Align the new shoe on the base of the sander and secure it with the three screws.

Fix Number

FIX12487158

Manufacturer Part Number

A23158

This is an OEM dust bag for your sander, and it is sold as an individual part. The dust bag connects to the sander to help control the dust created while sanding. This part includes the cloth bag and wire frame that secures it. There is also a zipper located at the bottom of the bag, which is used to easily empty it after each use. Over time the bag can wear or the zipper may damage. This is a quick, easy, and tool-free repair that you can do yourself. This dust bag is connected to the sander with a spring clamp. Press the two halves of the spring clamp together and pull it to remove. Take your new dust bag, pinch the clamp together and place the bag over the opening.

Fix Number

FIX12502235

Manufacturer Part Number

897159

Genuine OEM replacement part used on Belt Sanders. it is Sold Individually. This part consists of a Plastic Knob with a Metal Threaded Shaft. This part in conjunction with a Spring will allow you to Adjust Belt Tracking by turning the Knob in either direction until the edge of the belt is even with the outer edge of the rear rubber-covered pulley. Replacing this part is very easy and it does not require any additional tools.

Fix Number

FIX18995161

Manufacturer Part Number

N778654

Genuine Porter Cable replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX18982311

Manufacturer Part Number

5140112-36

This is a Genuine OEM Approved replacement part used on Porter Cable Sanders. This switch has a Plastic Body and it includes Metal Screws and Terminals. Switches are a commonly replaced part in power tools, handling on/off operations. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. To replace this switch you would need a Screwdriver. • First make sure the tools is not plugged in • Then you want to remove Screws used to hold two pieces of Housing Set together • Disconnect Wires from the old Switch and remove it from the Housing • Place the new Switch in the Housing and connect Wires to it • Reassemble the Housing

Fix Number

FIX12475150

Manufacturer Part Number

804211

This is a genuine replacement steel bearing from original manufacturer. It is commonly used in Porter Cable and Black & Decker belt sanders. Bearings are parts which separate metal parts to ease in movement and reduce friction. They also stabilize and prevent incorrect direction/tilt during movement. These high-wear parts are replaced regularly. This part is sold individually. Washers etc. sold separately.

★★★★★

★★★★★

1 Review

Fix Number

FIX12522806

Manufacturer Part Number

N031635

This part includes one carbon brush with a wire lead and brush spring attached. A poorly running motor is often due to worn brushes, which is why they are such a common repair in power tools. Due to the constant friction they are under, they will wear over time, and will need to be replaced. If upon inspection you notice the carbon brush is burnt or otherwise damaged, you will also want to check the condition of the armature, as this might suggest a larger problem with the motor.

Fix Number

FIX12514499

Manufacturer Part Number

908909

Genuine Porter Cable replacement part, this item is sold individually. The 4" Shoe Assembly attaches to the base of the 4x24 Belt Sanders listed below. The purpose of this part is to allow the sanding belt run against it, it helps to create a smooth flat sanded surface. It includes the metal platen cork & three mounting screws. Over time the platen and cork will start to wear. It should be replaced ASAP then. (4 Inch) Includes Cork and Screws

Fix Number

FIX18981344

Manufacturer Part Number

395373-04

This is a genuine manufacturer-approved replacement switch which is specially designed for use with Porter Cable belt sanders. It is the part of the tool handling on/off and variable speed operations, over time mechanical switches tend to wear out and may begin to fail eventually requiring replacement. Please note this high-quality plastic body switch is sold individually.