Bandfile Parts

Sander Idler Wheel Assembly

$151.53

Fix Number: FIX12023329
Manufacturer Part Number: 11011

This is a Genuine OEM sourced replacement part designed for Dynabrade Dynafile. This Idler Wheel helps to support and drive the Sanding Belt. It is made out of Metal and it is Sold Individually. This assembly includes the Wheel, Bearing and a Bolt that secures it.

Belt Guard

$6.51

Fix Number: FIX10130279
Manufacturer Part Number: 43-54-0615

An authentic OEM approved replacement component which is supplied for use with Milwaukee band files. This special guard is secured to the housing to protect the belt from dust and other debris. It is a high-quality part which is made of durable black plastic and it is sold individually, please note the hardware to secure it is sold separately.

Side Handle

$7.89

Fix Number: FIX10134116
Manufacturer Part Number: 49-15-0310

This replacement side handle is a genuine Milwaukee part, not an aftermarket imitation. It is sourced directly from original equipment manufacturer for use with sanders and grinders. This side handle helps you to better control the tool while it is in operation. It consists of a plastic handle and a metal threaded shaft. One item is included per order. Replacing this item does not require any tools.

Cord Set

$16.45

Fix Number: FIX10122674
Manufacturer Part Number: 22-64-0215

This is a cord set for your power tools. It is constructed with a tough outer-rubber insulation for a longer life span. The 18-gauge power cord is 8 feet long, and comes with 2 prongs and 2 wires. This cord is black in color and is sold individually.

Brush Spring

$6.51

Fix Number: FIX10123380
Manufacturer Part Number: 23-52-0240

This is a brush spring for your power tools. It keeps the brush tight against the armature. Over time the carbon brush will wear down, and heat will be created. This could cause your spring to lose tension, and will then have to be replaced. For this part to be in great working condition, it needs tension to keep the brush tight. When you replace your carbon brushes we recommend replacing your brush spring for an even wear, and to keep the spring in perfect working condition. This part is made from metal and is sold individually.

Knob

$19.69

Fix Number: FIX10340124
Manufacturer Part Number: 95218

This knob is an original part from Dynabrade and is used as a securing mechanism in the equipment listed below. This part consists of a plastic knob with a metal threaded shaft. Please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. This item is sold individually.

Contact Arm Assembly

$118.03

Fix Number: FIX12023348
Manufacturer Part Number: 11218

This item is a genuine Dynabrade part that is OEM sourced to ensure quality. The contact arm assembly is intended to be used with belt sanders. The contact arm assembly attaches to the idler arm and is used as the turn at the end of the belt loop. The assembly includes the front roller and belt pads. This item is priced as a single item.

Blades/rotor (4 Pack)

$42.41

Fix Number: FIX10336518
Manufacturer Part Number: 01011

These blades in your die grinders are located on the rotor within the motor housing. This OEM set includes four blades, each measuring approximately 1-1/2 inches by 3/8 inches. When the tool is turned on, the motor drives the rotor, causing the blades to spin rapidly and help you shape various materials. It is important to regularly check the condition of the blades and replace them if they are visibly worn out or misaligned. Additionally, pay attention to any unusual signs during operation, such as increased noise, vibration, or burning smells. To replace the blades, refer to your user manual for detailed instructions on how to disassemble the motor housing. Typically, you will need to secure the tool in a padded vise, then use an adjustable pin wrench to remove the lock ring. Proceed with disassembling the tool by removing the collet and rotor nut from the rotor shaft, followed by the cylinder, spacer, and the four blades from the rotor.

Carbon Brush Set

$60.73

Fix Number: FIX10337784
Manufacturer Part Number: 40750

It is an authentic manufacturer-sourced replacement set which is specially designed for use with Dynabrade power tools. The brushes play the key role by conducting electric current while maintaining physical contact with an armature. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem. This set includes two high-quality carbon brushes with attached lead wires.

Carbon Brush

$7.72

Fix Number: FIX10122198
Manufacturer Part Number: 22-18-0710

This carbon brush lead or also known as a carbon motor brush fits the following tools: angle grinders, nibbler and shears, sander polishers, and jig saws. This includes the brush and a wire lead attached. This is one of the most commonly replaced power tool components because the carbon brushes easily wear off with friction and use. If your brush is worn out it can cause intermittent motor function, reduction in electric braking, and in motor power. If you notice burns and cracks on the wire lead, then it is best to replace this part. Tip: when replacing your carbon brush, make sure to inspect your armature for damage as well, in case there are larger motor problems.

Popular Bandfile Parts

Bandfile Brands

Related Bandfile Parts

Popular Bandfile Models

Bandfile Parts

Start With Your Model Number

Popular Bandfile Parts

Bandfile Brands

Related Bandfile Parts

Popular Bandfile Models