Porter Cable Nailer Valves

Porter Cable Appliance Parts

Popular Porter Cable Nailer Valves

HEAD VALVE BODY
$6.25
In Stock
★★★★★
★★★★★
10 Reviews
Fix Number
FIX12417689
Manufacturer Part Number
180450-S
This is a genuine head valve for nailers and staplers. The head valve is responsible for controlling the flow of air to the cylinder. When the trigger is pulled, it creates an imbalance of pressure, which opens the head valve and fires the piston. The head valve is prone to wear over time, so it is important to inspect it often. The seals on the head valve or the body itself can begin to harden and eventually crack, and this results in air leaking from the gun exhaust. For this repair you will need an Allen wrench adjustable wrench and a screwdriver. This plastic head valve is sold individually.
Fixes these symptoms
  • Driver won't return
  • Leaks air from top
  • Won't fire
  • See more...
HEAD VALVE BODY
$6.25
In Stock
★★★★★
★★★★★
10 Reviews
Fix Number
FIX12417689
Manufacturer Part Number
180450-S
This is a manufacturer-approved replacement head valve and is sold independently. It controls the amount of air that enters the cylinder when the trigger is initiated. This action creates an imbalance in pressure between the cylinder and the air reservoir, allowing the head valve to open, firing the piston. The head valve can harden and crack and the valve body itself can break too. This will usually become obvious because air will leak from the gun exhaust. To access this part for the repair, you will need to remove the top cap from the nail gun.
Fixes these symptoms
  • Driver won't return
  • Leaks air from top
  • Won't fire
  • See more...
DRAIN VALVE
$7.60
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX12508562
Manufacturer Part Number
N286039
This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.
Fixes these symptoms
KIT-TRIGGER VALVE
$49.60
In Stock
Fix Number
FIX12531525
Manufacturer Part Number
TVA6
This is a genuine Bostitch replacement part that fits all BT brad nailers and all S32 staplers. If trigger leaks air or if tool misfires often, try replacing trigger valve. This kit contains one (1) each of: valve assembly (including both O-rings), lubricant, spring pin punch, and repair instructions. Please note that two (2) O-rings are included but can also be purchased separately as parts # 106967 and # 86459. O-rings are easily damaged and worn out, causing tool issues, so it\\\'s a good idea to have a backup or two on hand. Only a hammer is needed for this repair.
TRIGGER VALVE ASSY.
$28.42
In Stock
Fix Number
FIX18985719
Manufacturer Part Number
647620-00
It is a genuine Porter Cable replacement part, sold individually. The Trigger Valve Assembly regulates the compressed air via the trigger to your Nailer. Repair is fairly easy, requiring a small hammer and a punch pin. Remove trigger pin with punch pin, remove trigger, remove pins and valve assembly, clean area and lubricate o-ring is recommended, replace valve assembly and trigger. This part is compatible with the Nailers shown below.
Fix Number
FIX18979965
Manufacturer Part Number
149839
The lower body head valve goes between the sleeve seal and the head valve spring. This item is available as an individual replacement part. It is made of plastic and is an original Bostitch part for nailers. It can wear out over time and will need to be replaced. A screwdriver may be needed during the installation of this part.
Trigger Valve
$11.86
In Stock
Fix Number
FIX18990335
Manufacturer Part Number
9R202265-TW
This genuine OEM trigger valve in your nailer or stapler works in conjunction with the head valve. When you press the trigger valve, it creates a pressure difference between the air reservoir and the cylinder and causes the head valve to open and release compressed air to drive the nail or staple into the material you are working on. It is commonly found in the handle or grip area of the tool. If the trigger becomes stiff or difficult to press, the trigger valve may be damaged. To replace the trigger valve, begin by removing the magazine and retainer caps for the nosepiece guard. Take out the nosepiece from the housing and remove the roll pins securing the piston. Pull back the plastic guard on the housing, detach the strap securing the piston, and extract the piston from your tool. You can access and remove the trigger valve by taking out the O-ring and the pin that holds the trigger in place. Before reassembling the housing, remember to apply lubricant to the O-rings.
Fix Number
FIX18990652
Manufacturer Part Number
A08368
This unthreaded trigger valve assembly is a genuine OEM assembly used in nailers. It includes the trigger valve, 1 rubber washer, and 3 roll pins. The trigger valve controls the flow of air in the tool which drives the piston and creates the nailing action. If the valve becomes stuck, the seals wear down, or the trigger breaks the nailer will leak air, struggle to fire, or not fire at all. Begin the repair by switching off the tool and using a push pin to remove the trigger. Remove the roll pins that secure the trigger valve and pull the trigger valve out of the housing. Insert the new valve into the housing, install the pins to hold it in place, and secure the stay pin with the washer.
VALVE
$6.25
In Stock
Fix Number
FIX18990297
Manufacturer Part Number
9R201508
TRIGGER VALVE ASSY.
$38.57
In Stock
Fix Number
FIX18987821
Manufacturer Part Number
895212
This is an authentic Porter Cable replacement part manufactured for use with pneumatic nailers and staplers. The trigger valve assembly includes the valve guide, stem, valve head, spring, and o-ring. The valve assembly releases pressurized air to fire the piston and driver. The valve assembly is available as a kit and the kit is sold individually.

Related Porter Cable Nailer Parts