Miter Saw Seals and Gaskets

Fix Number

FIX10165223

Manufacturer Part Number

049787-00

It is a high-quality component which is supplied by the original equipment manufacturer for use with Dewalt and Black and Decker power tools. This replacement o-ring has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. It is made of durable rubber material and it is sold individually.

Fix Number

FIX10165195

Manufacturer Part Number

034158-00

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Fix Number

FIX10141724

Manufacturer Part Number

213021-5

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Fix Number

FIX10171370

Manufacturer Part Number

391315-00

An authentic manufacturer sourced replacement part that is specially produced for use with Dewalt miter saws. This is the gasket that is used to create a seal for the gear case assembly. Over time gaskets may get compressed and begin to crack eventually requiring replacement. It is made from high quality composite material and it is sold individually.

Fix Number

FIX10141889

Manufacturer Part Number

213460-9

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression</u> O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Fix Number

FIX10126936

Manufacturer Part Number

34-40-1375

This is a genuine manufacturer-sourced replacement o-ring which is specially designed for use with Milwaukee power tools. It is generally utilized to provide an air-tight seal between connected pieces, make sure to check appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable rubber material and is sold individually.

Fix Number

FIX16687195

Manufacturer Part Number

N510450

Fix Number

FIX10141722

Manufacturer Part Number

213011-8

Fix Number

FIX10166834

Manufacturer Part Number

153560-00

This is an authentic DeWalt replacement part that has been sourced from the original manufacturer to be used miter saws. The gasket is used to seal the connection between the gear/pinion and the arm assembly. This item is available as an individual replacement part.

Fix Number

FIX10166833

Manufacturer Part Number

153559-00