Hammer Drill Seals and Gaskets

Fix Number

FIX11878394

Manufacturer Part Number

44-90-0014

This c-ring is supplied directly from the original equipment manufacturer. The metal ring is compatible with the Milwaukee 1" D-Handle Rotary Hammer. This protective part is fitted between the chuck sleeve and the ball plate. Although the c-ring is sold individually, two are needed for the hammer. A screwdriver is needed for the replacement.

Fix Number

FIX10142024

Manufacturer Part Number

213962-5

This replacement o-ring is specially designed for use with Makita rotary hammers. It is an authentic manufacturer sourced item that is used to provide a seal for the striker and the piston. For correct location please make sure to check appropriate diagrams of your unit. Over time seals and o-rings tend to shrink, become brittle and crack eventually requiring replacement. Please note one durable rubber o-ring is included per order. Replacing this item you would need hex key which is also known as an allen wrench to complete the repair.

Fix Number

FIX10165223

Manufacturer Part Number

049787-00

It is a high-quality component which is supplied by the original equipment manufacturer for use with Dewalt and Black and Decker power tools. This replacement o-ring has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. It is made of durable rubber material and it is sold individually.

Fix Number

FIX10188475

Manufacturer Part Number

N114827

Fix Number

FIX10141850

Manufacturer Part Number

213379-2

This o-ring 21 is an OEM part direct from Makita. The flexible plastic ring is made for use with pneumatic nailers and rotary hammer tools. This item is often fitted between the compression spring and the driver, providing protection from friction. The o-ring 21 is sold individually. You will need a hex key for the repair.

Fix Number

FIX10127076

Manufacturer Part Number

34-40-5310

This is an authentic Milwaukee replacement part that has been sourced from the original manufacturer to be used with rotary hammers. The special o-ring is used to seal the space between the striker and the inside of the barrel. The o-ring is sold as an individual replacement part.

Fix Number

FIX10132129

Manufacturer Part Number

44-90-5262

This is an authentic OEM component from the Milwaukee manufacturer. The c-ring is used on many rotary hammer devices, and is sold individually. The metal ring secures the sleeve and the holding ring. A screwdriver and a pair of pliers are helpful in the repair.

Fix Number

FIX10141889

Manufacturer Part Number

213460-9

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression</u> O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Fix Number

FIX10180566

Manufacturer Part Number

590306-00

Fix Number

FIX10141862

Manufacturer Part Number

213406-5

This is a genuine OEM sourced replacement o-ring which is utilized on Makita power tools. This component provides an air-tight seal between connected parts, over time the material may become brittle and crack eventually requiring a replacement to ensure the proper seal. It is a high-quality component which is made of durable rubber and it is sold individually.