DeWALT Grinder Power Cords

★★★★★

★★★★★

1 Review

Fix Number

FIX10169875

Manufacturer Part Number

330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Fix Number

FIX10169913

Manufacturer Part Number

330079-98

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Fix Number

FIX10169655

Manufacturer Part Number

330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Fix Number

FIX11925999

Manufacturer Part Number

330081-18

This replacement item is used with Dewalt grinders. It is an authentic part supplied directly from original equipment manufacturer. This cord delivers power from the outlet to the tool. If the cord is damaged or torn it is important to replace it immediately and not use the tool until replaced. It is constructed with tough, thick outer rubber insulation for a long service life. Please note the cord protector/grommet is sold separately. Replacing cord is a simple repair that should only require a screwdriver. • Remove housing screws • Separate housing • Disconnect wires • Remove old cord • Secure new cord in place • Reattach wires • Reassemble and test the unit

Fix Number

FIX10169657

Manufacturer Part Number

330005-11

This is a Genuine OEM replacement Protector Grommet which is used on some Dewalt Angle Sanders. This part is made out of Rubber and is Sold Individually. It is important to have a cord protector on your tool to improve friction, seal cable and protect it from a potential damage.

Fix Number

FIX12529453

Manufacturer Part Number

N453825

Fix Number

FIX10172215

Manufacturer Part Number

401088-00

This cord protector is a genuine Dewalt replacement part. It is specially produced for use with angle grinders. It slides onto the power cord and fits securely at the end. The firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. It is made out of rubber and it is sold individually.

Fix Number

FIX10166291

Manufacturer Part Number

148809-00

This is a genuine OEM sourced replacement part designed for use with a variety of power tools. Cord guards, also called cord protectors, are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. It is made out of rubber and it is sold individually.

Fix Number

FIX10180872

Manufacturer Part Number

604567-00

This replacement cord and plug assembly is a genuine manufacturer sourced part that is specially produced for Dewalt angle grinders. If the cord is damaged it is important to replace it before continuing to use the tool. This high quality rubber insulated cord is sold individually, please note the protector sleeve is sold separately.

Fix Number

FIX12402079

Manufacturer Part Number

330081-98

This is a genuine part which is supplied directly by the original equipment manufacturer and is used with Porter Cable, Black and Decker, and Dewalt impact wrenches and drywall screwdrivers. When plugged into the wall, the power cord transfers power to the unit. This part is made of flexible plastic and metal, it is also sold individually. For installation, you will need a screwdriver to remove any covers or shrouds, and a pair of needle nose pliers to aid you.