Dust Collector Parts & Repair Help

$39.90

Fix Number FIX10325609

Manufacturer Part Number 489105-00

This Switch is an OEM approved replacement part for various tools and models manufactured by Delta, Black and Decker, and Porter Cable. For full compatibility, please see the "Model Cross Reference List" below. This Switch has four terminals, a removable safety key, and a compact design for easy installation. The purpose of the switch is to turn the device on/off, as well as playing a role in electric breaking by momentarily reversing electrical polarity. Due to the mechanical internals of switches, they tend to degrade and wear out over time, making them a commonly replaced part in power tools. Common symptoms of a broken switch include: the device has completely stopped functioning, it will not turn on, and turning off intermittently during use. Each Switch is sold individually, and may also be referred to as a Rocker Switch.

Installation Instructions

keith from EMPORIA, KS

Power switch would not turn saw off

unplugged power cord.
removed the nut holding the power switch assembly on the saw.
removed 3 screws from the back cover.
removed the 2 white wires and 2 black wires from the switch terminal post. pay attention to wire color on each post.
removed old switch from the bracket by squeezing the sides of the old switch to remove the switch from the bracket.
inserted the new switch in place in the opening.
re attached the wires to the spade terminal on the switch using the 4 terminals. black on the 2 posts top and bottom on one side and the other side white on the top and bottom.
re attach the switch assembly to the table saw
test operation Read more...

$64.24

Switch

Fix Number FIX10382827

Manufacturer Part Number 994542

$8.01

Brush

★★★★★

2 Reviews

Fix Number FIX10183735

Manufacturer Part Number 650916-01

Sold Individually This motor brush is for angle grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the angle grinder before installing this part. Wear work gloves to protect your hands.

Installation Instructions

Pam from BENBROOK, TX

Worn brush

Honestly I Utubed it, cause it was the first time I've done it and wanted to make sure I did it right, super easy. Read more...

$9.97

Key

Fix Number FIX10318424

Manufacturer Part Number 1343758

This safety key fits multiple hardware tools and is inserted into the switch to make it possible for your machine to turn on and operate. Tip: you can remove the key to prevent unauthorized use of the machine. For installation instructions refer to the diagram provided by the manufacturer.

$16.88

Power Cord

★★★★★

1 Review

Fix Number FIX10169875

Manufacturer Part Number 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

$44.10

Plastic Collection Bag (Set of 5)

Fix Number FIX10382130

Manufacturer Part Number 709563

$4.66

Primer Pump

Fix Number FIX8858167

Manufacturer Part Number 12318140630

This is a primer pump or primer bulb, and it is used on various outdoor lawn equipment. This part has an outer diameter of 0.616 inches, it is dome shaped, and transparent. The primer pump gives the engine of your machine a faster start by pulling fuel into the carburetor. If your pump is malfunctioning your machine will not receive the fuel it needs to operate properly. If you notice the primer pump is leaking you must replace it, as it could become dangerous.

Installation Instructions

Steve from Hilliard, OH

Replaced fuel line, primer,filter and hoes

In home shop Read more...

$50.97

Snap Ring

Fix Number FIX10458281

Manufacturer Part Number 331038

$56.95

Retainer Strap

Fix Number FIX10382877

Manufacturer Part Number AB410012

$7.59

Flange

Fix Number FIX10182961

Manufacturer Part Number 633257-00SV

This is an authentic OEM flange for angle grinders. It works with the nut (sold separately) to secure the grinding wheel to the gear case. It is imperative that they are maintained and inspected regularly to ensure they are still in good working condition to ensure no additional stress is put on the wheel. When making this repair, do not over-tighten the flange, as this could cause it to warp. This flange has 5/8-inch bore and is sold as an individual part.

Dust Collector Parts

Popular Dust Collector Parts

Brands

Popular Dust Collector Models

Dust Collector Parts

Start With Your Model Number

Popular Dust Collector Parts

Brands

Popular Dust Collector Models