Electric Drill Springs and Shock Absorbers

Fix Number

FIX11929265

Manufacturer Part Number

N019351

The compression spring is part of the impact drivers chuck assembly. The spring is found over the anvil shaft and provides tension to pull the chuck collar back after a bit is removed. Over time this part can lose tension or become damaged. A failed compression spring will cause the collar to move freely, and the driver bit will come loose. This is an OEM official part and is sold individually.

Fix Number

FIX10185154

Manufacturer Part Number

871690

It is a genuine item that is supplied by the original equipment manufacturer for use with DeWALT and Black and Decker power tools. It is an identical replacement for a missing or faulty spring that was installed on a new unit, unfortunately, over time it will wear out or may begin to crack eventually requiring a replacement. Keep in mind this high-quality part is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.

Fix Number

FIX10127907

Manufacturer Part Number

40-50-1090

This is an authentic Milwaukee replacement part manufactured for use with power tools. The special compression spring is used with a variety of different types of power tools. This spring is commonly used to allow flexibility between part assemblies and to prevent jarring between the part assemblies. This compression spring is sold as an individual replacement part, please see model diagram for part location and usage.

Fix Number

FIX10165211

Manufacturer Part Number

038769-00

Genuine OEM replacement part, this item is sold individually. This spring is used in various locations of the tools listed below. Over time springs will loose their tension and will need to be replaced. The dimensions on this spring are 5/16 in length and 3/16 in diameter.

Fix Number

FIX11877708

Manufacturer Part Number

40-50-0027

This replacement spring plate is an authentic OEM part which is made for use with Milwaukee power tools. The spring connects to the switch lever allowing it to retract. Over time it may wear out or get damaged eventually requiring a replacement to ensure your tool functions properly. Note, this high-quality spring plate is made of durable metal and is sold individually. You will need a screwdriver to take the tool apart in order to remove the old part and secure the new one. Refer to the appropriate diagrams of your specific model for the exact location of this hardware.

Fix Number

FIX16313052

Manufacturer Part Number

253428-3

This part is available individually. The spring washer fits between the wing nut and the flat washer. This washer is small and will need to be replaced if it gets lost or if it breaks. It is made out of metal and no tools should be necessary when replacing this item. This is an OEM Makita part directly sourced from the manufacturer for use with saws, cutters, planers, drills, and trimmers.

Fix Number

FIX10143359

Manufacturer Part Number

233005-7

This is a Genuine OEM replacement part used on Makita drills and drivers. This is a metal spring and it is sold individually. Over time springs may lose its tension and may not function as intended. If this part is lost or damaged it must be replaced. To replace this spring a pair of pliers is needed.

Fix Number

FIX10143367

Manufacturer Part Number

233025-1

This is a Genuine OEM replacement part used on some Makita Power Tools. This is a Metal Spring and it is Sold Individually. Over time springs may loose its tension and may not function as intended. If this part is lost or damaged it must be replaced.

Fix Number

FIX10187066

Manufacturer Part Number

N014681

Fix Number

FIX10122297

Manufacturer Part Number

22-20-0345

Genuine Milwaukee replacement part rnIncludes the assembled wire lead, brush spring and installation brackets for a carbon brush. Note: the carbon brush in not included. rnPlease go to the schematic listings for your tool to find the carbon brush compatible with this assembly and your tool. This assembly will fit the tools listed at the bottom of the page.rnrn As the carbon brush gradually wears away, the brush spring decompresses to keep the brush pressed against the armature in spite of the continual erosion of the brush. This ensures lasting tool performance, helping to prevent low motor power, reduced electric braking, and intermittent motor function. While brush springs aren't prone to failure, their small size makes them easy to lose while doing motor maintenance.