OEM Milwaukee Hammer Drill Parts & Accessories

Collet

$8.19

Fix Number: FIX10129511
Manufacturer Part Number: 42-77-0400

This is an authentically sourced collet for rotary tools. This collet is for using bits with 1/8-Inch arbors. Over time and heavy use, the collet will wear and will require replacing. You may need a collet nut wrench (sold separately) to remove the collet nut.

Brush Service Kit

$12.05

Fix Number: FIX10122270
Manufacturer Part Number: 22-18-6025

This is a genuine brush set designed for use with Milwaukee rotary hammers. This assembly includes two (2) carbon brushes with lead wires attached. Please note brush holders are sold separately. Due to prolonged contact with an armature brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. To complete this repair you would need a screwdriver. • Make sure the unit is unplugged • Remove screws from the housing to gain access to the armature and brushes • Remove old brushes and secure the new ones in brush holders • Re-assemble and test the tool

Watch the install video

Chuck Key

$13.92

Fix Number: FIX10134025
Manufacturer Part Number: 48-66-3280

This is an OEM chuck key and it is sold individually.The chuck key fits into a hole on the side of the chuck. The teeth are what help to hold the adjusting ring. As you rotate the key, the adjusting ring turns to tightly engage with the drill bit. This chuck key tightens jaws that have a 1/2-inch capacity. Over time, the teeth can deteriorate and this can cause the gear to slip. To make it easier to keep track of the chuck key, a chuck key holder can be ordered separately. It attaches to the power cord and the chuck key can be attached to it.

Brush Card Assembly

$18.88

Fix Number: FIX10122416
Manufacturer Part Number: 22-22-2602

This is a genuine brush card assembly for a drill/driver. The function of this part is to hold the carbon brushes around the armature, providing a secure contact. This assembly includes a plastic holder ring, four metal brush holders with springs and four carbon brushes with lead wires. For this repair you will need a screwdriver and will need to remove the cover to get access the part.

120v Carbon Brush

$6.51

Fix Number: FIX11877180
Manufacturer Part Number: 22-18-0032

This 120v carbon brush is an OEM direct from the Milwaukee manufacturer. Compatible with the 5262-21 (G43B) 1" SDS D-Handle Hammer, the brush is secured to the brush holder and armature. The purpose of brushes is to conduct current in an electric motor that powers the tool. This part is sold individually. A screwdriver is needed to make the proper removal and replacement.

C-ring

$6.51

Fix Number: FIX11878394
Manufacturer Part Number: 44-90-0014

This c-ring is supplied directly from the original equipment manufacturer. The metal ring is compatible with the Milwaukee 1" D-Handle Rotary Hammer. This protective part is fitted between the chuck sleeve and the ball plate. Although the c-ring is sold individually, two are needed for the hammer. A screwdriver is needed for the replacement.

Dust Cap

$6.51

Fix Number: FIX10129123
Manufacturer Part Number: 42-52-5262

This is an authentic Milwaukee replacement part manufactured for use with rotary hammers. The special dust cap is used to prevent debris from entering the sleeve. This dust cap is available as an individual replacement part, please see model diagram for associative parts.

Switch

$23.05

★★★★★

1 Review

Fix Number: FIX10123482
Manufacturer Part Number: 23-66-0177

This is an OEM trigger switch with four internal terminals. The switch controls the on/off and varying speed functions. It is common for the switch of a power tool to wear and malfunction over the use of a tool and require replacement. A few signs that will indicate a replacement is need is If the tool will not turn on when you engage the switch, it requires multiple tries to turn on, or the variable speeds are not working.

7mm Ball

$6.51

Fix Number: FIX10116750
Manufacturer Part Number: 02-02-0275

This is a genuine Milwaukee part that has been sourced from the original manufacturer to ensure a high level of quality. The steel ball is used to reduce friction between the gear case assembly. This item is sold as an individual replacement part.

Quik-Lok Power Cord Set

$54.95

Fix Number: FIX10134042
Manufacturer Part Number: 48-76-4008

This Milwaukee Quik-Lok® cord is a genuine OEM replacement part, it is sold individually. This is a three wire grounded 8 foot cord for fast field replacement of a damaged cord. Made of premium grade Hi-Flex wire the cord is quickly removed and attached to Milwaukee tools with the Quik-Lok® cord feature. To change a damaged cord simply turn the collar at the top of the cord counter clockwise to loosen the nut and pull down on the cord to remove. To re-attach a new cord, line up the pins in the end of the tool with the pin receptacles in the end of the cord, push together and turn the collar clockwise to lock in place. The Cord has a 5-15P NEMA type plug.

Installation Instructions

Brian from ATHENS, AL

Had a bad cord

Insert end turned to the right. Done. Read more...

Milwaukee Hammer Drill Parts

Popular Milwaukee Hammer Drill Parts

Installation Instructions

Milwaukee Hammer Drill Appliance Types

Related Milwaukee Hammer Drill Parts

Popular Milwaukee Hammer Drill Models

Milwaukee Hammer Drill Parts

Start With Your Model Number

Popular Milwaukee Hammer Drill Parts

Installation Instructions

Milwaukee Hammer Drill Appliance Types

Related Milwaukee Hammer Drill Parts

Popular Milwaukee Hammer Drill Models