OEM Porter Cable Electric Drill Parts & Accessories

Ball Bearing

$8.28

Fix Number: FIX10180907
Manufacturer Part Number: 605040-15

Genuine OEM sourced replacement part used on a variety of power tools. Ball bearings are used to reduce friction between rotating parts. Bearings experience constant wear when the tool is in operation, because of this they need to be periodically checked and replaced if needed. This part is made out of metal and it is sold individually. Included in part number 381004-00 spindle assembly.

Carbon Brush

$6.88

Fix Number: FIX10167153
Manufacturer Part Number: 176846-04

This is a single OEM carbon brush. Two are needed to make a set, so if you require two, order accordingly. Carbon brushes are used to conduct electricity to the armature through its commutator. Brushes are a common wear part that will need to be replaced periodically due to consistent rubbing against the rotating commutator. Worn brushes can cause sparks around the commutator, which can also cause damage to the armature, which should also be inspected. If your electric motor is experiencing issues, the brushes should be one of the first things you check.

Terminal

$6.51

Fix Number: FIX10173367
Manufacturer Part Number: 444262-00

This is a replacement part directly sourced from the manufacturer for use in drills, hammers, grinders, sanders, jigsaws, and trimmers made by DeWALT, Porter Cable, Black & Decker, and Bostitch. It connects to the power cord and is made out of metal. This part is extremely small and will need to be replaced if it becomes lost or if it breaks. The terminal is sold individually.

BRUSH & SPRING

$10.47

Fix Number: FIX18993274
Manufacturer Part Number: N119739

This carbon brush and spring assembly helps maintain proper electrical contact within the motor, allowing your power tool to run smoothly and reliably. Designed for consistent performance, it supports efficient power transfer to the motor components. Replacing worn brushes can resolve issues such as intermittent operation, excessive sparking, or failure to start, restoring normal tool function.

Watch the install video

Power Cord

$23.86

★★★★★

1 Review

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

BRUSH

$12.09

Fix Number: FIX18985827
Manufacturer Part Number: 690741

Genuine Porter Cable replacement part rnIncludes 1 Carbon Brush with lead.rnrn n++ Worn brushes are often the cause of a poorly running motor n++ Replacing brushes can fix an intermittent motor n++ New brushes can restore a motorn++s electric braking Carbon motor brushes are one of the most commonly replaced power tool components.n++ Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement.n++ Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power.n++ A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned.n++ When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

CHUCK, 13MM, WEIDA, P3 LC DRIL

$13.21

Fix Number: FIX18988894
Manufacturer Part Number: 90591283

This is an authentic Porter Cable replacement part that has been sourced from the original manufacturer to be used with drill/drivers. The chuck is used as a vice that fastens and holds the drill and driver bits. A screw driver is needed to install this part, please note the screw that secures the chuck is reverse threaded. The chuck is sold individually.

Watch the install video

Keyless Chuck

$47.25

Fix Number: FIX10188921
Manufacturer Part Number: N196034

This genuine replacement keyless drill chuck is designed for quick, tool-free bit changes and reliable performance during demanding drilling and driving tasks. Built with a durable metal construction and an automatic locking mechanism, it provides a strong grip to help minimize bit slippage, even in high-torque applications. The chuck supports a wide range of bit sizes and installs directly onto the drill spindle, making it an effective solution for restoring accuracy, stability, and ease of use when an existing chuck is worn or damaged.

Gear

$13.77

Fix Number: FIX11929795
Manufacturer Part Number: N437049

This is a genuine replacement part that has been sourced from the original manufacturer to be used with electric drills from DeWalt, Black and Decker, and Porter Cable. The metal gear is used to link the armature assembly and the chuck's spindle shaft. This item is priced as a single item.

BRUSH & RETAINER ASY

$15.19

Fix Number: FIX12504955
Manufacturer Part Number: 874289

Genuine Porter Cable replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Porter Cable Electric Drill Parts

Popular Porter Cable Electric Drill Parts

Installation Instructions

Porter Cable Electric Drill Appliance Types

Popular Porter Cable Electric Drill Models

Porter Cable Electric Drill Parts

Start With Your Model Number

Popular Porter Cable Electric Drill Parts

Installation Instructions

Porter Cable Electric Drill Appliance Types

Popular Porter Cable Electric Drill Models