OEM Makita Cordless Drill Parts & Accessories

Housing Set

$29.29

Fix Number: FIX16302376
Manufacturer Part Number: 183E34-9

This housing set is a replacement enclosure designed to protect internal components and maintain structural integrity. It is commonly replaced when cracked, worn, or damaged from impact or heat.

Flat Washer

$6.51

Fix Number: FIX10144369
Manufacturer Part Number: 253804-1

Genuine Makita replacement part, it is sold individually. This washer is used in various areas in the tool model numbers shown below. It is used as a washer for a screw or bolt or even as a spacer.

Keyless Drill Chuck 13bdf452hw

$55.02

Fix Number: FIX11885251
Manufacturer Part Number: 766027-7

This is an OEM sourced replacement part designed for use with Makita drills/drivers. It allows user to secure drill bits. The ratcheting action clicks the jaws tightly into place for reduced bit slippage. If your drill\'s bit retention is suffering, the rotation feels stiff, or the chuck has seized up entirely, a new chuck should fix the problem. Please note the screw used to secure this chuck it is sold separately.

Carbon Brush Set

$14.45

★★★★★

1 Review

Fix Number: FIX10156660
Manufacturer Part Number: CB430

This CB430) Makita carbon brush set contains two individual carbon brushes. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed below. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Ball Bearing

$26.20

Fix Number: FIX10141520
Manufacturer Part Number: 211031-6

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Belt Hook

$6.51

Fix Number: FIX10149281
Manufacturer Part Number: 346449-3

Brush Holder

$8.88

Fix Number: FIX10153308
Manufacturer Part Number: 638614-1

This is an Authentic Manufacturer Sourced replacement part used on a Makita Drills/Drivers. This part consists of: Plastic Holder Ring, Two (2) Metal Brush Holders With Springs and Two (2) Lead Wires Attached. This part holds Carbon Brushes around the Armature to provide stable and safe contact. Please note Carbon Brushes are Sold Separately. To replace this assembly you would need a Screwdriver and Pliers. • First remove Screws holding the cover together. • Carefully remove Two (2) Halves of the housing to gain access to Armature and Brush Holder. • Remove the screws holding Brush Holder to The Trigger. • Remove the Armature Assembly and the Brush Holder. • Install the New Brush Holder, Brushes and the Armature • Reassemble and test your tool.

Watch the install video

Terminal

$8.88

Fix Number: FIX10153397
Manufacturer Part Number: 643852-2

This part includes one genuine battery terminal for a cordless drill. This part is where the battery terminals connect. It is a plastic block that has metal spades, which engage the contacts on the battery. If the battery shorts or the drill overheats, this can cause damage to the terminal. If you notice melted plastic around the spades or the spades themselves have melted or are discolored, these are also signs that a replacement is required. The wire connections are another area to take note as these can cause issues with the terminal too. For this repair, remove the rear cover, separate the housings, and slide the terminal out. Be sure to take note of the wire connections and disconnect them from the terminal assembly.

Watch the install video

Brush Holder

$6.08

Fix Number: FIX10153287
Manufacturer Part Number: 638494-5

This is an Authentic Manufacturer Sourced replacement part used on a some Makita Drills/Drivers. This part consists of: Plastic Holder Ring, Two (2) Metal Brush Holders and Two (2) Lead Wires Attached. This part holds the Carbon Brushes around the Armature to provide stable and safe contact.

Watch the install video

Change Lever

$6.51

Fix Number: FIX10150817
Manufacturer Part Number: 419250-0

This is a genuine Makita replacement part, it is sold individually. The purpose of the F/R Change Lever is to change the rotation of the drill motor. It connects to the switch of the tools listed below. By pressing it left or right this will change the rotation of the drill.

Makita Cordless Drill Parts

Popular Makita Cordless Drill Parts

Makita Cordless Drill Appliance Types

Related Makita Cordless Drill Parts

Popular Makita Cordless Drill Models

Makita Cordless Drill Parts

Start With Your Model Number

Popular Makita Cordless Drill Parts

Makita Cordless Drill Appliance Types

Related Makita Cordless Drill Parts

Popular Makita Cordless Drill Models