Boring Machine Parts

Plain Washer

$6.51

Fix Number: FIX11929226
Manufacturer Part Number: N016823

This is a genuine OEM plain washer and is part of your impact driver chuck assembly. The washer fits over the compression spring and provides a flat surface for the hog ring to sit against. This part usually needs to be replaced because it has been lost during the disassembly of the chuck. To begin this repair, remove the hog ring from the chuck, being mindful not to misplace the spring. Now you can place the compression spring in place and the new washer over top and reinstall the hog ring. Use a pair of needle nose pliers to push the compression spring as you install the hog ring over the spindle.

BRUSH & SPRING

$10.47

Fix Number: FIX18993274
Manufacturer Part Number: N119739

This carbon brush and spring assembly helps maintain proper electrical contact within the motor, allowing your power tool to run smoothly and reliably. Designed for consistent performance, it supports efficient power transfer to the motor components. Replacing worn brushes can resolve issues such as intermittent operation, excessive sparking, or failure to start, restoring normal tool function.

Watch the install video

Carbon Brush And Holder Set

$21.17

★★★★★

1 Review

Fix Number: FIX10187386
Manufacturer Part Number: N031214

This part contains two carbon brushes and holder sets. Carbon brushes are a routine maintenance task, as they are prone to wear due friction. Worn brushes are the most common reason for a motor that is not running properly or at all. In general, this is a pretty easy repair, but keep in mind that instructions can vary slightly depending on the model. To access the brushes, you will need to remove the housing of the tool and the brushes will be located inside the holders close to the motor.

Watch the install video

Keyless Chuck Jacobs, 3/8

$25.83

Fix Number: FIX10169886
Manufacturer Part Number: 330075-46

This is an OEM sourced replacement part which is specially designed for use with DeWALT and Black and Decker drills. It allows user to secure drill bits. The ratcheting action clicks the jaws tightly into place for reduced bit slippage. If your drill's bit retention is suffering, the rotation feels stiff, or the chuck has seized up entirely, a new chuck should fix the problem. NOTE: This 3/8" capacity chuck mounts to the drill using a 1/2"-20 threaded spindle. The light-weight plastic design provides comfort while the keyless two-sleeve construction adds the efficiency and ease-of-use of keyless bit-swapping. See our post on <a href="http://forums.ereplacementparts.com/power-tool-repair/8-removing-cordless-drill-chuck.html" target=blank_<u>Removing a Cordless Drill Chuck</a> if you need help replacing your old chuck.

Vsr Switch

$46.15

Fix Number: FIX10182274
Manufacturer Part Number: 621884-03

This is an authentic manufacturer approved replacement switch used on DeWALT drills. It is the part of the tool handling on/off and variable speed functions. Since switches have moving mechanical parts, they will eventually wear out and will require a replacement. Switch has a plastic body and it is sold individually. To replace this switch you would need a screwdriver. • Remove screws used to hold two pieces of housing set together • Disconnect wires from the old switch and remove it from the housing • Place the new switch in the housing and connect wires to it • Reassemble the housing

Watch the install video

Brush Box

$13.49

★★★★★

1 Review

Fix Number: FIX10180814
Manufacturer Part Number: 603754-01

The brush box assembly is used on a variety of cordless tools and appliances. This assembly includes a carbon brush spring and holder. Carbon brushes are commonly replaced because they wear out easily with friction. If your brush is worn out it disrupt the function of the motor and reduce electric braking. Tip: to check if the brush is worn out inspect the wire lead for cracks burns and other damage. Replacing the brush can restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions. *Please note: This part is sold individually.

Handle,spade

$13.87

Fix Number: FIX10182689
Manufacturer Part Number: 628037-00

This is an original replacement part manufactured for use with drills. This hardened plastic spade handle is secured at the back of the drill using a knob, which is available separately. The spade handle provides an additional grip option for heavy duty drills, please note the spade handle is sold individually.

CHARGER

$25.40

Fix Number: FIX18989568
Manufacturer Part Number: 90640340

Genuine Manufacturer Sourced replacement part used on some Black and Decker Power Tools. This item is sold individually. Purchasing a charger will be less expensive than buying a new tool. Please note that a weak or defective battery can damage the charger. Weak batteries are batteries with bad cells. These type of batteries will not hold a charge. It will send a message to the charger to keep charging. This will eventually cause the charger to overheat and potentially smoke.

Carbon Brush

$6.88

Fix Number: FIX10167153
Manufacturer Part Number: 176846-04

This is a single OEM carbon brush. Two are needed to make a set, so if you require two, order accordingly. Carbon brushes are used to conduct electricity to the armature through its commutator. Brushes are a common wear part that will need to be replaced periodically due to consistent rubbing against the rotating commutator. Worn brushes can cause sparks around the commutator, which can also cause damage to the armature, which should also be inspected. If your electric motor is experiencing issues, the brushes should be one of the first things you check.

BRUSH & RETAINER ASY

$15.19

Fix Number: FIX12504955
Manufacturer Part Number: 874289

Genuine Porter Cable replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Popular Boring Machine Parts

Boring Machine Brands

Related Boring Machine Parts

Popular Boring Machine Models

Boring Machine Parts

Start With Your Model Number

Popular Boring Machine Parts

Boring Machine Brands

Related Boring Machine Parts

Popular Boring Machine Models