Circular Saw Seals and Gaskets

Fix Number

FIX16649810

Manufacturer Part Number

5690373001

Fix Number

FIX16640415

Manufacturer Part Number

3706396001

This genuine manufacturer-sourced part is specially designed for use with Skil and Bosch saws. The purpose of this gasket is to provide a tight seal for the housing, unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. Keep in mind this high-quality component is made of durable composite material and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.

Fix Number

FIX10132369

Manufacturer Part Number

45-06-0720

It is an authentic item that is supplied directly from the original equipment manufacturer for use with Milwaukee saws. This special seal helps to provide a tight fit between connected components. It is an identical replacement for a missing or a worn part that was installed on a new unit. Please make sure to refer to the appropriate diagram of your model for the exact location and application of this part. Keep in mind this high-quality seal is made of durable felt material and is sold individually.

Fix Number

FIX10141889

Manufacturer Part Number

213460-9

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression</u> O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Fix Number

FIX10126937

Manufacturer Part Number

34-40-1380

This is available as an individual replacement part. The o-ring hub is made of rubber and goes between the hub and gear. A screwdriver, a set of pliers, and a wrench set may be needed during the replacement of this part. It may become broken and will need to be replaced. This item is an original part from Milwaukee for use in saws.

Fix Number

FIX10141718

Manufacturer Part Number

213005-3

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Fix Number

FIX16649812

Manufacturer Part Number

5690375001

Fix Number

FIX10126936

Manufacturer Part Number

34-40-1375

This is a genuine manufacturer-sourced replacement o-ring which is specially designed for use with Milwaukee power tools. It is generally utilized to provide an air-tight seal between connected pieces, make sure to check appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable rubber material and is sold individually.

Fix Number

FIX16676215

Manufacturer Part Number

050056-00

This is an authentic manufacturer sourced replacement part that is specially produced for use with Dewalt and Black and Decker power tools. The purpose of an o-ring is to provide and air-tight seal between two connected parts, over time it may deteriorate and crack eventually requiring replacement.It is made of durable rubber material and it is sold individually.

Fix Number

FIX11824798

Manufacturer Part Number

585280901

This is a genuine manufacturer sourced replacement part designed for use with Husqvarna lawn and garden equipment. It provides an air-tight seal for the muffler, over time the material may become brittle and crack eventually requiring a replacement. This part is made of high-quality composite material and it is sold individually.