Band Saw Brushes

Popular Band Saw Brushes

Carbon Brush
$6.51
In Stock
Fix Number
FIX10122113
Manufacturer Part Number
22-16-0275
This is a carbon brush, it is also known as a motor brush, and it is used with various power tools and equipment. The brush transfers electric currents to the motor. Your motor brush is an extremely common replacement part. It is considered a wear part, because the constant friction will wear it down. If you are experiencing a poor running motor, you will need to replace this part. New brushes will restore your motors electric braking. We recommend also inspecting your armature for damaging cracks or burns, this can indicate a larger problem in your motor that will require attention.
Fix Number
FIX10122190
Manufacturer Part Number
22-18-0670
This part includes one carbon brush with spring. Two of these brushes are needed in most models, and we recommend replacing them both at the same time, as they tend to wear at the same rate. A worn brush often affects the performance of the motor, and that is usually the first indication that a replacement is needed. For this repair, you will need to use a screwdriver to remove the brush cap which holds the brushes in place. To install, align the new brush with the holder and insert it by aligning the wings with the sides of the holder. Press the brush into the holder and secure the cap back on. Never over-tighten the cap, as this could break it. These steps will need to be repeated on the other side for the second brush.
BRUSH & RETAINER ASY
$16.77
On Order
Fix Number
FIX12504955
Manufacturer Part Number
874289
Genuine Porter Cable replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Tire Clearing Brush Kit
$7.37
In Stock
Fix Number
FIX10131232
Manufacturer Part Number
44-60-0295
This part is an OEM from Milwaukee. The tire clearing brush kit is made for use with many bandsaws. The kit includes a tire clearing brush, tire clearing brush cover and two screws. This kit removes debris from the blade, and is sold individually. A hex key is required for making the installation.
BRUSH-WIRE
$113.45
In Stock
Fix Number
FIX19133634
Manufacturer Part Number
JT9-5714111
Carbon Brush Assembly
$6.51
In Stock
Fix Number
FIX10122131
Manufacturer Part Number
22-18-0020
This replacement part is sourced directly from the original manufacturer for use with compact band saws. This item is secured between the cap and brush tube assembly on each side of the service armature. The purpose of brushes is to conduct current in an electric motor that powers the tool. This assembly includes one carbon brush with a lead wire and a spring attached. Please note it is advised to replace both brushes at the same time to ensure even wear. This part is sold individually. A screwdriver is needed to make the proper removal and replacement.
BRUSH
$93.67
In Stock
Fix Number
FIX19150183
Manufacturer Part Number
JT9-HVBS7MW-100
BRUSH
$6.51
On Order
Fix Number
FIX18981751
Manufacturer Part Number
5140075-07
This is an OEM replacement part for Porter Cable band saws and is sold individually. This plastic component attaches to the brush holder with a screw and washer to ensure that the blade's teeth do not become obstructed. Simply unscrew using a screw driver to replace this part.
Brush Tube Housing
$7.56
In Stock
Fix Number
FIX10122274
Manufacturer Part Number
22-20-0020
It is a genuine item which is supplied directly from the original equipment manufacturer for Milwaukee power tools. This is an identical replacement for a missing or damaged brush tube housing that was installed on a new unit. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this durable part is made of high-quality plastic and is sold individually.
Tire Cleaner Brush
$6.51
In Stock
Fix Number
FIX10131398
Manufacturer Part Number
44-60-2429