Screwdriver Parts

Carbon Brush Set

$16.59

Fix Number: FIX10156657
Manufacturer Part Number: CB408

This part includes two carbon brushes with wire leads and brush springs. Worn brushes are typically presented as a failed or underperforming motor. Carbon brushes are a part that commonly wears, so it is a good idea to have these on hand. They are essential for a properly running motor because they conduct electricity to the armature. For this repair, you will start by removing the first brush from the motor, using a screwdriver to remove the brush cap. Once the cap is removed, the brush can be removed. Align the new brush with the holder and then reinstall the cap. Repeat these same steps for the other brush.

Watch the install video

Carbon Brush Set

$16.59

Fix Number: FIX10156656
Manufacturer Part Number: CB407

This set comes with two carbon brushes with wire leads and brush strings attached. If your motor is not running efficiently or is operating intermittently, this is a common sign of worn brushes. Due to the friction they are constantly under, they will wear over time, and will start to appear cracked, pitted, or burnt if not replaced regularly. We recommend also taking a look at the armature to ensure it is not damaged. This brush set is compatible with multiple model types, so it is best to consult your user manual for repair instructions.

Watch the install video

Carbon Brush Set

$10.36

Fix Number: FIX10156662
Manufacturer Part Number: CB440

The brush box kit fits a variety of cordless gardening tools. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder. Due to friction, carbon brushes are common replacement parts. If the functioning of your motor changes and does not work, then check if the brush is worn out or inspect the wire lead for cracks, burns and other damage. Replacing the brush can restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions.

Clutch Assembly

$53.85

Fix Number: FIX10172536
Manufacturer Part Number: 429634-00

This is an authentic manufacturer approved replacement part designed for use with drills/screwdrivers. This clutch assembly is connected to the transmission and the shaft. Keeping an eye on equipment performance will determine when the clutch requires replacement. Includes part numbers 176842-00, 89210-00

Carbon Brush

$6.88

Fix Number: FIX10167153
Manufacturer Part Number: 176846-04

This is a single OEM carbon brush. Two are needed to make a set, so if you require two, order accordingly. Carbon brushes are used to conduct electricity to the armature through its commutator. Brushes are a common wear part that will need to be replaced periodically due to consistent rubbing against the rotating commutator. Worn brushes can cause sparks around the commutator, which can also cause damage to the armature, which should also be inspected. If your electric motor is experiencing issues, the brushes should be one of the first things you check.

Cord Protector

$6.51

Fix Number: FIX17061542
Manufacturer Part Number: N918736

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

Charger

$20.97

Fix Number: FIX17016372
Manufacturer Part Number: 90593303-01

This is a genuine Black and Decker replacement charger, sold individually. It’s designed to recharge the battery used in the cordless tools listed below. Over time, chargers can wear out or stop functioning properly. Replacing the charger is a cost-effective solution that can extend the life of your tools—often much less expensive than purchasing a brand-new unit.

GROMMET

$6.55

Fix Number: FIX19508139
Manufacturer Part Number: 2600703013

Ball Bearing

$20.36

Fix Number: FIX16680871
Manufacturer Part Number: 605040-20

This Ball Bearing has metal shielding on both sides. This is a genuine Dewalt replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Ball

$6.51

Fix Number: FIX10184189
Manufacturer Part Number: 696631-00

Genuine Dewalt replacement part, this item is sold individually. The 696631-00 Steel Ball is part of the chuck assembly of the Impact Drivers shown below. When you pull back the sleeve of the chuck assembly and insert your bit, the Steel Ball is the part that locks the bit in the chuck assembly. In the Screw Drivers listed below this is the part that secures the Bit Holder in the spindle.

Popular Screwdriver Parts

Screwdriver Brands

Related Screwdriver Parts

Popular Screwdriver Models

Screwdriver Parts

Start With Your Model Number

Popular Screwdriver Parts

Screwdriver Brands

Related Screwdriver Parts

Popular Screwdriver Models