Leaf Blower / Vacuum Switches

★★★★★

★★★★★

1 Review

Fix Number

FIX16431030

Manufacturer Part Number

760961002

Fix Number

FIX18783493

Manufacturer Part Number

291632001

This switch and contact plate assembly, also known as a wiring harness, is sourced from the original manufacturer for use in blowers. The switch controls the flow of electricity to either start or stop the blower, and the contact plate allows for electrical connection. The assembly can fail due to short circuits, faulty wiring, damage, or normal aging. A faulty switch and contact plate will result in difficulties starting the blower, lack of speed control, and fluctuating power output. Begin the repair by disconnecting the blower from the power source. Remove the blower housing and switch cover to access the assembly. Take note/image of the wire connections for the installation later. Disconnect the wire connectors and carefully pull the faulty assembly out of the blower. Position the new switch and contact plate assembly in the equipment and reconnect the wire connectors to the appropriate terminals using your notes/image from earlier. Reassemble the equipment parts in reverse order.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX10170531

Manufacturer Part Number

383994-00

This is a Genuine Manufacturer Sourced replacement part used on a variety of Black and Decker Trimmers/Edgers. This item is Sold Individually. Switches are a commonly replaced part in power tools, handling on/off operations. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement.

Fix Number

FIX10014381

Manufacturer Part Number

791-182405

This switch is used on a variety of trimmers, blowers and other similar gardening equipment. This switch controls the on and off operations of your tool. Switches have mechanical internals, which degrade and wear out in time. In this case, switches are a commonly replaced part. *Please note: this part is sold individually. The tool needed for this repair is a screwdriver. To repair, first remove screws that hold the pieces of housing together. Next, disconnect wires from the old switch as well as the wires from the housing. Now you can install the new switch in the housing and connect the correct wires to it. For further installation instructions, refer to the diagram provided by the manufacturer.

Fix Number

FIX10097329

Manufacturer Part Number

44905

This is a genuine OEM sourced replacement part designed for use with Ridgid portable power drive. Switches are a commonly replaced part in power tools, handling on/off operations. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. This switch has a plastic body and it is sold individually. To replace this switch you would need a Screwdriver.

Fix Number

FIX18789333

Manufacturer Part Number

760649001

Fix Number

FIX18789306

Manufacturer Part Number

760338004

This is an authentic OEM sourced replacement momentary contact switch. It is specially designed for Homelite and Ryobi blowers and vacuums. It is the part of the tool handling on and off function of the tool. Please note, these mechanical switches have will over time wear out requiring replacement. This switch has a plastic body and it is sold individually. To replace this item no tools would be needed.

Fix Number

FIX8876301

Manufacturer Part Number

16340003460

This is an OEM component that is specially made for use with an Echo and Shindaiwa handheld lawn and garden equipment. The ignition switch is used to turn the engine on or off. Unfortunately, over time it may wear out and begin to fail eventually requiring a replacement. This high-quality ignition switch is sold individually. You will need a screwdriver to take apart the housing in order to perform this repair.

Fix Number

FIX16391193

Manufacturer Part Number

651395-0

★★★★★

★★★★★

1 Review

Fix Number

FIX9282784

Manufacturer Part Number

503718201

This is an original replacement part manufactured for use with trimmers. The start/stop switch is also called the kill switch, and fits on the upper handle above the throttle. The red switch is used to shut of the engine, and has to be engaged to run the engine. The switch is sold individually.