Official Ariens Lawn Mower Hardware

Washer Head Screw

$6.51

Fix Number: FIX9982804
Manufacturer Part Number: 584953901

This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missing altogether. It is sold individually and is made of metal. You will need a wrench to remove the old screw and tighten the new one.

Lawn Mower Ring Clip

$6.51

Fix Number: FIX9143890
Manufacturer Part Number: 812000029

This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part of a mower wheel or steering assembly). When it is installed, the part that is visible acts as a shoulder, holding the specific component or assembly together. This very small metal ring clip (approximately 1-inch by 1-inch) is sold individually.

Shoulder Bolt

$6.51

Fix Number: FIX17089372
Manufacturer Part Number: 596434404

This is a genuine Husqvarna replacement part sourced directly from original equipment manufacturer for use with lawn mowers/tractors. It is commonly used in riding mowers to keep the gauge wheel in place. This is a hex head bolt which requires a wrench for installation. It is sold individually.

Lawn Mower Mandrel Spacer Washer

$7.16

Fix Number: FIX9286886
Manufacturer Part Number: 532187690

This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are approximate). In general, washers help to spread load, can provide insulation such as electrical, and can also help to prevent galvanic corrosion.

Bolt and Washer Assembly

$13.02

Fix Number: FIX9020856
Manufacturer Part Number: 532193003

This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If your lawnmower blade is not rotating properly or making grinding sounds, these are usually the first signs that that the bolt and washer may be worn. For this beginner repair, start by making sure the engine is cool, the spark plug is removed, and the mower is on its side. Remove the old bolt and washer with a socket. Insert the new bolt and washer into the blade opening and secure it with the socket.

Lawn Mower Washer

$6.51

Fix Number: FIX9008998
Manufacturer Part Number: 532121749

This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to spread the load under a bolt or screw. It also helps to reduce heat and friction as the fastener is tightened. This repair may require a screwdriver or socket wrench, depending on the fastener for your model. This is a single flat washer; the fasteners are sold separately.

Lawn Mower Hardened Washer

$6.51

Fix Number: FIX9015920
Manufacturer Part Number: 532188967

This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly over the surface and provides a solid grip.

Lawn Mower Flangelock Hex Nut

$6.51

Fix Number: FIX9022497
Manufacturer Part Number: 532409149

This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most models require three. For this repair you will need a wrench set.

Lawn Mower Push Nut

$6.51

Fix Number: FIX9285696
Manufacturer Part Number: 532110452

This is a genuine Craftsman replacement part for use in lawn tractors. It helps to connect the deflector rod to the deflector shield. The metal push nut is a small part and will need to be replaced if it becomes lost or broken. A screwdriver and a set of pliers may be needed to replace this part. This item is sold individually.

Flange Top Lock Nut

$6.51

Fix Number: FIX16381821
Manufacturer Part Number: 596134801

This high-quality item is an authentic OEM hardware that is designed for use with Craftsman riding lawn mowers and garden tractors. It is one of the locknuts that is utilized to secure the pulleys. A locknut is a nut that resists loosening under vibration and torque. Refer to the diagrams of your model for the exact location and the correct application of this part. One durable metal locknut is included. You will need a wrench to secure and remove it.

Ariens Lawn Mower Hardware

Popular Ariens Lawn Mower Hardware

Related Ariens Lawn Mower Parts

Ariens Lawn Mower Hardware

Start With Your Model Number

Popular Ariens Lawn Mower Hardware

Related Ariens Lawn Mower Parts