Chainsaw Bearings

Fix Number

FIX9006914

Manufacturer Part Number

532009040

This is a premium-quality OEM front wheel flange bearing (sometimes called bushing) commonly used in riding lawn mowers. They are used to keep the wheel held in place securely. It is sold individually but two are needed for each front wheel. It is recommended that they be replaced at the same time. Install this part with the flat side facing the grease zerk in the rear side of the wheel.

Fix Number

FIX9285698

Manufacturer Part Number

532110485

This is a single mandrel ball bearing for a mower. It is sold individually, however it is a good idea to have a couple of these on hand. This bearing is located on top of the shaft, which is part of the mandrel assembly. The mandrel assembly is bolted to the more deck. This bearing measures roughly 1-3/8-Inches inner diameter, 1.578-Inches outer diameter, and .475-Inches long.

Fix Number

FIX9006893

Manufacturer Part Number

532006266

The thrust washer fits next to the ring and the 16 gauge washer. This is an authentic Craftsman replacement part used in compatible lawn tractors. This item is priced as an individual replacement. It is made of metal and may require a pair of pliers during the replacement of this part if it becomes broken.

Fix Number

FIX9929713

Manufacturer Part Number

2515811-S

This manufacturer-supplied replacement part is designed for use with Kohler engines commonly installed on lawn and garden equipment. The bushing helps to secure the throttle linkage. It provides an identical replacement for a missing or a faulty hardware that was installed on a new unit. Please refer to the appropriate diagrams of your model for the exact location and the correct installation of this part. Keep in mind this high-quality bushing is made of durable plastic and is sold individually. You will need a wrench set to remove the housing in order to gain access to the bushing.

Fix Number

FIX10116859

Manufacturer Part Number

02-04-0910

This is an authentic part produced by the original manufacturer. It is compatible with Milwaukee power tools including grinders, sanders, and polishers. Ball bearings secure moving parts, allowing for free movement while reducing friction. They are high wear parts that may need regular replacement for optimal performance from tools. Sold individually.

Fix Number

FIX10141492

Manufacturer Part Number

210059-1

This authentic replacement part which is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, over time components may begin to wear out and fail eventually requiring a replacement. Please note this high-quality ball bearing is made of durable metal and it is sold individually.

Fix Number

FIX8960493

Manufacturer Part Number

38-7820

This is a Genuine Manufacturer Approved replacement part used on Toro Snowthrowers. This Ball Bearing has multiple applications in the Snowthrowers. This part is made out of Metal and it is Sold Individually. Ball Bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement. To replace this Bearing you would need a Screwdriver and a Set of Wrenches.

Fix Number

FIX19502030

Manufacturer Part Number

1609B02987

Fix Number

FIX18203404

Manufacturer Part Number

599531501

This OEM part is compatible with various models of Husqvarna chainsaw. Bearings buffer and stabilize moving parts so that friction and damage are reduced. Needle bearings facilitate spinning motion. Bearings are very high wear parts and may need replacement often. Sold individually.

Fix Number

FIX10141552

Manufacturer Part Number

211106-1

This Ball Bearing is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.