( Grid squares measure 1x1 inch )

Maintenance Kit

★★★★★
★★★★★
10 Reviews
$40.12
Fix Number: FIX373087
Manufacturer #: 4392065
Manufactured by: Whirlpool

Product Description

This is an authentic drum support roller kit for 29-inch-wide dryers. It includes 1 belt, 2 roller wheels and an idler pulley. The parts in this kit allow the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension needed for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If these parts are damaged, it could cause loud noises such as squeaking and squealing while the drum is turning. These are normal wear parts and are best replaced as a kit to ensure optimal performance.

Videos For installing this part.

Replacing your Maintenance Kit

Replacing your Maintenance Kit play video
Questions and Answers

Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Edmond
January 3, 2023
Making noise when tumbler turn
For model number Red4516fwo
Hello Edmond, thank you for contacting us. The issue is caused by a damaged belt, worn-out rollers, or a defective pulley. The most likely solution is to replace the maintenance kit, part number FIX373087. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!

Was this helpful?
Thank you for voting!

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.4 / 5.0, 52 reviews.
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
  • Customer:
    Steve from South Lake Tahoe, CA
  • Parts Used:
    4392065, WP4391960, 279318
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Defective heater element dryer still runs.
Expect to spend a lot of time on your knees. Unplug appliance. Remove dryer hose. remove back cover 4-6 7mm bolts. Unplug dryer heater element connections 2 blade or pin connectors. Unbolt element cover and remove old element. Label wires. Hopefully the replacement connections match if not go to hardware store. Crimp or better solder on new connectors. Install element in housing and reattach. Clean out all old dirt and lint. check old belt for wear and re-grease drum roller shafts. re-install back cover, hose and plug in. enjoy you just saved $600
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Dan from Cambridge, MA
  • Parts Used:
    4392065
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Dryer drum belt broke
I bought the maintenance kit which included the belt, roller wheels & tensioning arm assembly. The instruction video was great, but I had a real problem trying to get the belt through the tensioning arm and on to the motor pulley. As someone else has pointed out, It seem that you need three hands, and there's not enough room for two people. After a bit of pondering, I got some scrap bits of wood and wedged "open" the tensioning arm such that the wheel was a bit beyond it's position in the final assembly. This was easily accomplished with only two hands. The belt was then easily threaded through the arm and put around the motor pulley. The wood bits were then removed. TA-DA!
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Paul from Clarence Center, NY
  • Parts Used:
    4392065
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Drive belt broken. No drum rotation.
Following the instructions supplied, threading the new belt was easy. Support rollers installed really easily and the new idler pulley just snaps in. It was a good time to vacuum the interior, since the door panel was off, and to vacuum out the vent pipe. The instructions call for a small putty knife as a "shoe horn", to seat the rear drum seal, which really worked nicely. The trickiest part is holding the drum, while coaxing the door panel into place, so that the lower spring clips catch and the mounting screws can be started.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Lance from Macomb Township, MI
  • Parts Used:
    4392065
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Noisy, high speed bearing issue
Watched the installation video from this site performed the repairs and the Dryer works like new. Longest part of the repair was vacuuming the cabinet out and cleaning the shafts for the replacement parts. The total repair time, with cleaning was approximately a hour. Definitely recommend this site for any Do-It Yourself consumers!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    jack from Gilbert, AZ
  • Parts Used:
    4392065
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Squeaky Dryer
I followed the video instructions and had no problem changing the parts and even the belt while I was at it. The most challenging part was getting the inside electrical cables unplugged from one another before taking the front panel off the dryer.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Paul from Peoria, AZ
  • Parts Used:
    WPW10463866, WP694089, 4392065
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Bad motor and drum belt.
Open the top of the washer with a flat screwdriver it pries open. Removed the top two 5/16 screws from the inside of the front panel and removed the front panel, It has no screws at the bottom. Then remove four 1/2 nuts from the drum panel and remove the drum panel. Take the drum belt off of the drum and remove the drum. Remove the motor by unplugging the one big wire plug and two single blue wires. Be sure to take note of the location that each of the blue wires came from. The blower fan on the outside end of the motor unscrews clockwise and the motor is held in place with two clips. One on each side of the motor. The two drum rollers are each held on with a bolt in the center of them. After the motor is in place the new blower fan is threaded on counter clockwise on the motor shaft. Put the blower fan cover panel back on and reassemble the dryer. make sure the drum belt is in alignment with the motor pulley Also make sure the drum felt around the drum is not folded or torn and reinstall the drum panel. Spin the drum to check for metal on metal and or drag from roller alignment. Reinstall the front panel and close the top of the dryer.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Ray from Wilton, WI
  • Parts Used:
    4392065
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Noisy dryer
Unplug dryer, take two screws out of lint catcher, pop top with putty knife and lay back, take two screws out of front panel, slide off, lay machine on its back, apply pressure to tensioner to take off belt, remove drum, it's really light, swap out drum rollers and tensioner, put drum back in, make sure felt seal is in place, put belt back on, and reassemble.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Charles from Frankfort, IN
  • Parts Used:
    4392065
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
some of the new parts could not be used (too difficult to install)
I used the videos on you tube. The installation would have gone much smoother but some of the new parts could not be used due to the extreme difficulty in installing them. These part included the white triangle keepers for the rollers, the slip washer that keeps the left roller bracket in place, and the tension roller. I had to use the old parts that I had removed. This model does not use the roller type tension system. It uses the Teflon strip instead of the roller which apparently incapable.I made attempts to contact your customer service to check on a solution but to no avail. The dryer is working fine but I would feel better if I could have installed all the new parts in the kit.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Donald from Fountain Valley, CA
  • Parts Used:
    4392065
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
Loud, squeeking and grinding when tumbling
I watched the brief instruction video which exactly showed how to replace the parts in my dryer. So simple, highly recommended.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Kim from Gastonia, NC
  • Parts Used:
    4392065
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Dryer drum stopped turning. Motor still turned
I followed the easy video instructions. It took the mystery out of it. Replaced belt, 2 rollers, tension device. Some folks claimed to have difficulty getting the belt onto the motor pulley once it was thru the tensioner. The trick was to take a big screw driver and slide it into the belt loop as it goes through the tensioner. Then simply use the screw driver as a pry bar. Pull a little to the right and it sleeps right on. I saved a bunch of money. Will purchase all of my appliance parts from here now. Service was fast!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating: (10 Reviews)
4.9
★★★★★
★★★★★
Filter By Rating:
  • 5
    9
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    0
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Model Compatibility
This part works with the following models:
Fix Number: FIX373087
Manufacturer Part Number: 4392065
Brand
Model Number
Description
Kenmore
11060012001
Dryer
Kenmore
11060172001
Dryer
Kenmore
11060232001
Dryer
Kenmore
11060522900
Dryer
Kenmore
1106062110
Dryer
Kenmore
11061202010
Dryer
Kenmore
11061202011
Dryer
Kenmore
11061252010
Dryer
Kenmore
11061252011
Dryer
Kenmore
11062102310
Dryer - 29" ELECTRIC DRYER
Kenmore
11062202101
Dryer
Kenmore
11062212101
Dryer
Kenmore
11062512101
Dryer
Kenmore
11062514101
Dryer
Kenmore
11062602101
Dryer
Kenmore
11062612101
Dryer
Kenmore
11062622101
Dryer
Kenmore
11062702101
Dryer
Kenmore
11062712101
Dryer
Kenmore
11062722101
Dryer
Kenmore
11062724101
Dryer
Kenmore
11062802101
Dryer
Kenmore
11062812101
Dryer
Kenmore
11062822101
Dryer
Kenmore
11062824101
Dryer
Kenmore
11062852101
Dryer
Kenmore
11062872101
Dryer
Kenmore
11063102100
Dryer
Kenmore
11063112100
Dryer
Kenmore
11064102300
Dryer