Maytag Dryer Roller Shaft WP6-3129480 | Fix.com

Roller Shaft

&SeePartX&
11743031-1-S-Whirlpool-WP6-3129480-Roller Shaft
11743031-2-S-Whirlpool-WP6-3129480-Roller Shaft
11743031-3-S-Whirlpool-WP6-3129480-Roller Shaft
https://fixcom.azureedge.net/Schematics/Maytag/59071.gif
Click for the BBB Business Review of this Appliances - Small - Supplies & Parts in Dartmouth NS
Part Description:
This roller shaft is the axle for the drum roller, also known as drum roller axle.
This part fixes the following symptoms: Noisy, Will not tumble.
This part works with the following brands:
Part number cross reference:
This part works with the following products:
Dryer, Washer Dryer Combo, Range.

Installation Videos

Replacing your Maytag Dryer Roller Shaft
Watch this how to video with simple, step-by-step instructions for a successful DIY repair.
Fixes the following symptoms:
  • Noisy
  • Will not tumble
Tools used for this repair:
  • 5/16 nut driver
  • 9/16 wrench
  • Snap ring pliers
  • Stubby Philips screw driver

Installation Instructions

Showing 1-10 of 21 Instructions
>
page 1 of 3
<

Dryer was a bit noisy with a full load of wet clothes

As per the repair videos on the site, I searched the internet for a couple of supplementary videos just to make sure I was doing it correctly. It was was all pretty easy. Expect to vacuum out and clean out the interior of the dryer. Also, to make things easier, disconnect the bulkhead and exterior like in the video, but also keep the top flipped up until reassembling, it'll make it much easier. When reinstalling the belt, remember how the belt is going to go around the pulley, you'll have to do this without sight as the barrel will the way and you won't be able to see what you're doing. It's really not hard but just keep this in mind. Also, as you disassembling, it would help to snap some pictures of where each screw goes and how; reassembly was a tiny bit tricky as I didn't do this.

Were these instructions helpful?

2 of 2 people found these instructions helpful
Parts Used: Idler Pulley Wheel and Bearing , Roller Shaft , Multi Rib Belt - 91-5/8&quot; , Front Glide Kit , Drum Support Roller Kit , Retaining Ring
Difficulty Level: Easy
Total Repair Time: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Tim from PORTLAND, OR

Squeaking noises while running dryer

Followed the Video Directions from website. All went as planed. The dryer is running like new now.

Were these instructions helpful?

1 of 1 people found these instructions helpful
Parts Used: Roller Shaft , Idler Pulley Wheel , Tumbler and Motor Belt , Idler Pulley Shaft Washer , Front Glide Kit , Drum Support Roller Kit , Retaining Ring , Idler Shaft Retaining Ring
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Brian from Novi, MI

Replace drum rollers and their shafts

followed applianceparts video on youtube,although dryer somewhat different(older) ....video made the repair happen...

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Roller Shaft , Drum Support Roller Kit
Difficulty Level: Easy
Total Repair Time: 1- 2 hours
Tools: Nutdriver, Screw drivers, Socket set
Customer: donald from franklin lakes, NJ

Dryer had squeaking noise

Remove door and front panel remove drum replace drum support roller and roller shaft.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Roller Shaft , Drum Support Roller Kit
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Wrench set
Customer: Eric from Fort Bragg, CA

Dryer was making noise like an indy car now like a prius

Exactly like in the online video. The video was an excellent tool for this repair. Thank you, !

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Roller Shaft , Idler Pulley Wheel , Tumbler and Motor Belt , Drum Support Roller Kit
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Pliers
Customer: Steven from Troy, OH

Noisy

I pulled the entire unit apart, because I didn't , for sure, know what the problem was. I'm glad I did as it had years of crud and dust in it. The shaft and roller were easy to install. The belt routing was the hardest part, which was actually simple. It now makes no noise and dries really good.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Roller Shaft , Drum Support Roller Kit
Difficulty Level: Really Easy
Total Repair Time: More than 2 hours
Tools: Screw drivers, Wrench set
Customer: Randall from Valrico, FL

Dryer was extremely noisy squeeling and sqeaking

Followed installation videos and removed entire front of cabinet including door, loosened belt and removed drum. Only problem was the snap ring pliers I had were too large to fit in the holes of the drum roller snap ring. Ended up taking two 3 inch deck screws with sharp points, putting them in the snap ring holes and removing the ring by that method. Did the same when replacing it although this time, had to have my wife put a flat screwdriver against it while I pulled it apart with the screws. Rest of the repair was quite easy and dryer works great.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Idler Pulley Wheel and Bearing , Roller Shaft , Multi Rib Belt - 91-5/8&quot; , High Limit Thermostat (Limit: 200-30) , Drum Support Roller Kit
Difficulty Level: Easy
Total Repair Time: More than 2 hours
Tools: Nutdriver, Screw drivers, Socket set, Wrench set
Customer: John from McAllister, MT

Periodic screeching sound

1. bought the only snap ring pliers available at homedepot. 2. turned off the gas and unplugged 3. moved it away from back wall. 4. removed front panel. 5. removed drum housing. 6. slid off belt. 7. removed drum. 8 found one frozen roller and a second with roller washer severely worn washer. The pins on the snap ring plier were too large to insert into the spring rings. ground the small pins down with a power grinder until finally fit. (took a long time). Finally fit well enough to get retaining rings off. 9. replaced both shafts and rollers, though it was unclear whether the solid shafts needed replacement. 10. from rear, removed access panel and replaced idler pulley wheel. 11. placed drum back with new belt, then fit it over motor and pulley. Took a bit to get it fitted correctly. Much easier from rear panel than reaching around. 12. reinstalled housing and front panel. Problem areas: GET A SMALL SNAP RING PLIERS THAT WILL FIT ! Easier to install belt around idler pulley wheel from rear access panel. Replacement of roller shafts was probably not necessary. Works great now.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Roller Shaft , Idler Pulley Wheel , Tumbler and Motor Belt , Drum Support Roller Kit
Difficulty Level: Easy
Total Repair Time: 1- 2 hours
Tools: Screw drivers, Socket set, Wrench set
Customer: Robert from Encinitas, CA

Very loud rubbing/squeaking noise

Watched 2 YouTube videos. 1. How to take apart a dependable care dryer. 2. How to replace a belt on a maytag dryer. We replaced all the parts. It was eeasy. When putting dryer back together make sure felt is straight. We did have to take it apart again there was felt sticking out inside the dryer and it caused the drum to not spin. Everything works great. And Thank you parts select. I received the right parts in 2 days without paying extra. I will use you again.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Idler Pulley Wheel and Bearing , Roller Shaft , Multi Rib Belt - 91-5/8&quot; , Drum Support Roller Kit
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Tammy from Fremont, OH

Drum vibration

I removed the drum per instructions provided on the web site. Removed the two roller shafts. Installed the two new roller shafts and applied grease to the shaft. I secured the two rollers using the existing snap rings. I reassembled the dryer in the reverse order of dis assembly. Machine runs like it did when it was new. Easy job.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Roller Shaft , Drum Support Roller Kit
Difficulty Level: Really Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Alton from Greenbrier, TN
Showing 1-10 of 21 Instructions
>
page 1 of 3
<

Model Cross Reference List

This part works with the following models:

Fix Number: FIX11743031
Manufacturer Part Number: WP6-3129480


Brand Model Number Description
Roper2570B00Range - Electric
Roper2570B10Range - Electric
CrosleyCDE4205AYJDryer - Residential
CrosleyCDE4205AYWDryer - Residential
CrosleyCDE4205AZJDryer - Residential
CrosleyCDE4205AZWDryer - Residential
CrosleyCDG4205AWJDryer - Residential
CrosleyCDG4205AWWDryer - Residential
MaytagDE106Dryer - Electric
MaytagDE107Dryer - Electric
MaytagDE110Dryer - Electric
MaytagDE18CADryer - Electric
MaytagDE18CMDryer - Electric
MaytagDE18CSDryer - Electric
MaytagDE18CTDryer - Electric
MaytagDE19CADryer - Electric
MaytagDE19CDDryer - Electric
MaytagDE19CSDryer - Electric
MaytagDE19CTDryer - Electric
MaytagDE210Dryer - Electric
MaytagDE212Dryer - Residential
MaytagDE21CADryer - Electric
MaytagDE21CMDryer - Electric
MaytagDE21CSDryer - Electric
MaytagDE21CTDryer - Electric
MaytagDE22CADryer - Electric
MaytagDE22CSDryer - Electric
MaytagDE22CTDryer - Electric
MaytagDE23CDDryer - Electric
MaytagDE24CADryer - Electric