Kenmore Dryer Rear Drum Support Roller Kit 349241T | Fix.com

Rear Drum Support Roller Kit

&SeePartX&
347627-1-S-Whirlpool-349241T           -Rear Drum Support Roller Kit
https://www.fix.com/Schematics/Whirlpool/SNBNEJXS.gif
Click for the BBB Business Review of this Appliances - Small - Supplies & Parts in Dartmouth NS
Part Description:
This is a rear drum support roller kit for your dryer. The 2 rollers come with 4 tri-rings, and 1 palnut. We recommend that you replace both rollers at once. This kit stabilizes the drum cylinder, allowing the dryer to tumble properly. If you are having problems with your appliance during tumble mode, or if it is too noisy, you will need this kit.
This part fixes the following symptoms: Noisy, Will not tumble, Will not start, Marks left on clothes.
This part works with the following brands:
Part number cross reference:
This part works with the following products:
Dryer, Washer Dryer Combo.

Installation Videos

Replacing your Kenmore Dryer Rear Drum Support Roller Kit
Watch this how to video with simple, step-by-step instructions for a successful DIY repair.
Fixes the following symptoms:
  • Loud rumbling noise while dryer drum is turning
Tools used for this repair:
  • 5/16 Nut Driver
  • Phillips Screw Driver
  • Putty Knife

Related Parts

Installation Instructions

Showing 1-10 of 18 Instructions
>
page 1 of 2
<

The roller support wheels were worn down and needed replacing.

Step 1: removed power source.
Step 2: removed screws from lent catcher.
Step 3: removed top lid.
Step 4: removed front panel.
Step 5: removed drum.
Step 6: removed plastic washers.
Step 7: removed old wheels.
Step 8: installed new wheels.
Reversed steps to put everything back.

Were these instructions helpful?

5 of 5 people found these instructions helpful
Parts Used: Rear Drum Support Roller Kit
Difficulty Level: Very Easy
Total Repair Time: 15 - 30 mins
Tools: Screw drivers, Socket set, Wrench (Adjustable)
Customer: Tyrik from KENNESAW, GA

The dryer squeeled the full time it was turned on.

I called my boyfriend

Were these instructions helpful?

2 of 2 people found these instructions helpful
Parts Used: Idler Pulley Assembly , Rear Drum Support Roller Kit , Multi Rib Belt - 92-1/4"
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Cathy from WHITE HAVEN, PA

Noise,banding

Replaced the wheel that holds the drum

Were these instructions helpful?

1 of 1 people found these instructions helpful
Parts Used: Rear Drum Support Roller Kit
Difficulty Level: Really Easy
Total Repair Time: 30 - 60 mins
Tools:
Customer: Elaine from Round lake park, IL

Squeeks like crazy while running

I replaced the drum rollers, belt and idler pulley, I had an 80-90% chance that it would fix the issue. The video on the website was spot on in every phase of the repair - just follow it as shown. By spending $45, I bet I'll get many more years out of this machine.

Were these instructions helpful?

1 of 1 people found these instructions helpful
Parts Used: Idler Pulley Assembly , Rear Drum Support Roller Kit , Multi Rib Belt - 92-1/4"
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Screw drivers, Wrench set
Customer: David from Rochester, NH

Bearing worn out

simple

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Rear Drum Support Roller Kit
Difficulty Level: Really Easy
Total Repair Time: 15 - 30 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Rosemarie from Dedham, MA

Rubber on support roller was breaking and rubbing off. Replaced belt while in there.

Pulled belt off rollers removed drum from dryer then replaced. Removed bad roller. Hardest part was getting the triangle past the first groove to the second. Cleaned shaft with towel and greased with lithium then put roller and second triangle on. Put drum back in and hook belt back on. I watched a video on you tube that showed step by step.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Rear Drum Support Roller Kit , Multi Rib Belt - 92-1/4"
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable)
Customer: Lorianne from Lancaster, OH

Really noisy dryer

Repair was made so easy with the video! I found the repair video on youtube first and ordered the parts from partselect. The parts arrived very quickly. I watched the video again to make sure I knew what I was doing, took the dryer apart, and had the new rollers installed, dryer put back together, and clothes drying in about half an hour. Thanks so much!

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Rear Drum Support Roller Kit
Difficulty Level: Really Easy
Total Repair Time: 15 - 30 mins
Tools: Socket set
Customer: Nicole from Bluffton, IN

Noisy

Nephew came and repaired hit for me, it went very easy, it was all done with a hour

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Rear Drum Support Roller Kit
Difficulty Level: Really Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Cindy from Sherburn, MN

No heat,dryer belt was broken,drum wheels were replaced

Just like you showed in your instructions. But I am going to put the old idler pulley back in cause the new one makes a loud whining noise. Other than that it should be fine. The service I received from you guy's was great.This was a simple repair. Thank's again Bill

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Idler Pulley Assembly , Rear Drum Support Roller Kit , Multi Rib Belt - 92-1/4"
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: william from phoenix, AZ

Idler pulley froze up.

Replaced idler pulley, and belt. Also changed drum rollers while had everything open. Followed online videos. Worked perfect.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Idler Pulley Assembly , Rear Drum Support Roller Kit
Difficulty Level: Really Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Everette from Winnsboro, SC
Showing 1-10 of 18 Instructions
>
page 1 of 2
<

Model Cross Reference List

This part works with the following models:

Fix Number: FIX347627
Manufacturer Part Number: 349241T


Brand Model Number Description
Kenmore10686294140Dryer
Kenmore10686294340Dryer
Kenmore10686294540Dryer
Kenmore10686294740Dryer
Kenmore10686294840Dryer
Kenmore10688419100Dryer
Kenmore10688419300Dryer
Kenmore110088732791Washer Dryer Combo
Kenmore11060012000Dryer
Kenmore11060012001Dryer
Kenmore11060012002Dryer
Kenmore11060022010Dryer
Kenmore11060172000Dryer
Kenmore11060172001Dryer
Kenmore11060172002Dryer
Kenmore11060202990Dryer
Kenmore11060212990Dryer
Kenmore11060232000Dryer
Kenmore11060232001Dryer
Kenmore11060232002Dryer
Kenmore11060522900Dryer
Kenmore11060602990Dryer
Kenmore11060612990Dryer
Kenmore1106062110Dryer
Kenmore11060622990Dryer
Kenmore11060702990Dryer
Kenmore11060712990Dryer
Kenmore11060722990Dryer
Kenmore11060724990Dryer
Kenmore11060727990Dryer