OEM General Electric Dryer TOP BEARING [WE03X25079] | Ships Today | Fix.com
TOP BEARING – Part Number: WE03X25079
TOP BEARING – Part Number: WE03X25079 TOP BEARING – Part Number: WE03X25079 TOP BEARING – Part Number: WE03X25079 https://fixcom.azureedge.net/Schematics/GE/3E7E85634D91687E5B75924AEE8CD3279C29C5FD.gif

TOP BEARING

Your Price
$26.89

Fix Number: FIX12342893

Manufacturer #: WE03X25079

Manufactured by: GE

Get this part fast. Average delivery time via standard shipping: 1.8 days.

Part description

Note: The drum slides should also be replaced when your replacing the drum bearing. Slides are NOT included. This part helps your dryer operate as quietly as possible.

Works with the following brands

General Electric, Hotpoint, Kenmore

Works with the following products

Dryer, Washer Dryer Combo

Fixes the following symptoms

Noisy | Marks left on clothes

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.2 / 5.0, 6 reviews
Customer:
Gary from Fort Lauderdale, FL
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Loud squeeking noise. Louder when machine had heavy load.
Unplug machine. Remove two screws holding top on. They're inside the door, upper left and right corners. Lift front of top cover, swing up and slip the back edge tabs out of slots in top cover. Set cover aside. Remove two screws that hold sides to front panel. Pull top of front panel toward you 5 or 6 inches. Lift front panel free from base of machine and set it down close to the machine. Unplug wires for door switch and light located on lower left inside of panel. Panel is now free to move away from machine. Remove light bulb. Push down on the two vertical tabs on the upper part of drum bearing and pull bearing off front panel, discard. Line up new bearing and snap into place. I had to press and align the bearing to get it into proper position. Install guide strips, I needed 4. The hole in the guide goes over the pin in the bearing. Flex the guide until it can slip into the slot in the bearing. Don't worry they only go in one way. Reinstall light bulb. Move front panel close enough to machine to reconnect wires. Lift front panel onto base, leave a few inch gap at the top of the front panel. Open the door, put your hand inside and push the drum up slightly. Pivot the front panel back so it's up against side panels. Replace screws, top left and right holding front panel to sides. Replace top, hold front of lid higher in front. Line up the three tabs on the control panel with the three slots on the back edge of the lid. Swing the lid down like you would close the hood of a car. May have to play with it a bit but it will go. Replace the two screws inside the door cavity. Plug machine in and test. While the machine was apart I cleaned the duct work with a shop vac.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
CRAIG from ROANKE, VA
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Squeaking drum
Unplug. Remove 2 screws from top left-right inside dryer door opening. Remove screws holding timer-controls from back. Lift up cover. Remove 2 short screws inside left-right top holding front panel. Tilt out top front while holding drum up. Remove dryer bearing asembly from dryers frontpanel and replace new parts. Reaaemble.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Dan from Chesterton, IN
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Very squeeky noisy!!! with or with out load
If your slide bearings are worn bad. The top Bearing(plastic housing) that holds the 4 slide bearings might be damaged, mine was warn to the point where the slide bearings would not mount to the old top bearing. Remove the two screws that hold the top of the dryer in place. (inside the door at the top) Lift the top from the front and work it out from the back top(control panel) pay attention how this tucks in the back. Next remove the two bigger screws from the inside next to the top of the drum that attach the front panel. remove the front panel partially so you can get the electrical connections on the door switch. Use needle nose pliers to un plug the connection on the switch and pull the other apart. remove front panel. take the panel to a bench or table after you clean all the lint trapped in the exhaust duct. remove old felt, install new felt the same way the old one was attached. now pry the top bearing from its plastic clips. Install the new bearing. Install the new bearing slides on the new bearing. re-connect the electrical connections with the front panel sitting on the floor in place. then put the front panel in from the bottom first, it sits in two perches. then pivit forward and install the front cover over the drum and onto the new bearings. install screws. install top cover from the back first, this is the trickiest part. pay attention and lift the front high to get the back tucked in under the control panel, then lower the top cover until it all pops together , don't force it! once it is in place open the door and install the 2 remaining screws. The dry will make a slight scrapping sound until the new slide bearings are worn in (2 or 3 loads) No more squeaky noisy DRYER!
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Kenneth from Barrington, RI
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Dryer was squeeking loudly
Searched Internet for dryer model squeeking. Found probable cusses. Watched video. Took dryer apart found the above parts worn out. Changed the belt and idler pulley just because I had the dryer apart. Less than 50 minutes dryer is fixed. Dryer is like news for $133.00
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Luther from Sacramento, CA
Parts Used:
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers
Dryer was making a turblence and started to eat clothings
Took the top and front off, saw that the bearing sides were worn and gone. Replaced the back bearing setup and belt while I had it open. would have been nice that the bearing sides came as a set and the houseing that they setin. Time was wasted waiting for the top bearing sides (green ones) to come in. They were completely gone as was one white one and part of the housing. It took about 8 hrs. in repair time as I am Disabled. Should of taking about 3 hrs with all parts on hand.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Robert from El Cajon, CA
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Worn dryer drum slides
The repair video of our dryer (which was subsequently taken off the website) was very helpful and showed exactly how to replace the top drum bearing and slides. Since I am out of state I was able to direct my wife, who has little mechanical experience, to the video on the website and then provide her with additional assistance over the phone. It was an easy repair and the video was very helpful in showing me how to make the repair so I could advise my wife. Thanks for the help. I will definitely use you for repairs in the future.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

Fix Number: FIX12342893
Manufacturer Part Number: WE03X25079
Brand
Model Number
Description
Kenmore
2661532413
Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore
2661532513
Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore
2671532413
Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore
36361542411
Washer Dryer Combo - HOME LAUNDRY COMBO
General Electric
GHDP490EF3WW
Dryer - DRYER
General Electric
GHDP490EF4WW
Dryer - ELECTRIC DRYER
General Electric
GHDP490EF5WW
Dryer - ELECTRIC DRYER
General Electric
GHDP490EF6WW
Dryer - ELECTRIC DRYER
General Electric
GHDP490GF3WW
Dryer - DRYER
General Electric
GHDP490GF4WW
Dryer - GAS DRYER
General Electric
GHDP490GF5WW
Dryer - GAS DRYER
General Electric
GHDP490GF6WW
Dryer - GAS DRYER
General Electric
GTD18ESSJ0WW
Dryer - ELECTRIC DRYER
General Electric
GTD18ESSJ1WW
Dryer - ELECTRIC DRYER
General Electric
GTD18ESSJ2WW
Dryer - ELECTRIC DRYER
General Electric
GTD18GSSJ0WW
Dryer - GAS DRYER
General Electric
GTD18GSSJ1WW
Dryer - GAS DRYER
General Electric
GTD18GSSJ2WW
Dryer - GAS DRYER
General Electric
GTDL210ED4WW
Dryer - ELECTRIC DRYER
General Electric
GTDL210GD4WW
Dryer - GAS DRYER
General Electric
GTDL210GD5WW
Dryer - GAS DRYER
General Electric
GTDN550ED4WW
Dryer - ELECTRIC DRYER
General Electric
GTDN550ED5WW
Dryer - ELECTRIC DRYER
General Electric
GTDN550GD4WW
Dryer - GAS DRYER
General Electric
GTDN550GD5WW
Dryer - GAS DRYER
General Electric
GTDP180ED4WW
Dryer - ELECTRIC DRYER
General Electric
GTDP180ED5WW
Dryer - ELECTRIC DRYER
General Electric
GTDP180ED6WW
Dryer - ELECTRIC DRYER
General Electric
GTDP180GD5WW
Dryer - GAS DRYER
General Electric
GTDP180GD6WW
Dryer - GAS DRYER