Westinghouse Washer Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Westinghouse Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Westinghouse Washer Parts

Single Shock Mounting Pin – Part Number: 131268300
Single Shock Mounting Pin
$22.91
In Stock
Fix Number
FIX417323
Manufacturer Part Number
131268300
This washer shock absorber mounting pin is a small but essential fastener that secures the shock absorber to the outer tub of a front-load washing machine. By holding the shock absorber firmly in place, it helps stabilize the tub during wash and spin cycles, reducing excessive vibration, shaking, and movement. Made from durable materials and designed for a precise fit, the pin supports smooth operation and protects other components from stress caused by unbalanced motion. Replacing a worn, broken, or missing mounting pin can help restore proper vibration control, improve washer stability, and prevent noise or damage during operation.
Watch the install video
Bellow Kit – Part Number: 134515300
Bellow Kit
$199.66
In Stock
Fix Number
FIX1148773
Manufacturer Part Number
134515300
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle. NOTE: This part has been redesigned by the manufacturer and is interchangeable with the old design.
Fixes these symptoms

Installation Instructions

Linda from Los Angeles, CA
needed new bellow...full of black mold
It was actually "a handy man" who did the repair. The "instruction" that you provided me with sounded somewhat complicated, and at first he tried to install the rubber bellow from the front. I told him "no" it looked from your instructions he had to pull the machine out and unscrew back etc. I do not think I could have figured it out on my own...he did, and it is now installed and working. It is NOT an easy installation however...If he had not had your instructions, I am not certain he would have been successful!> but..."all's well that ends well." Read more...
Watch the install video
Drive Belt - 6 ribs – Part Number: 134051000
Drive Belt - 6 ribs
$25.10
In Stock
Fix Number
FIX419285
Manufacturer Part Number
134051000
This is a drive belt for your washing machine. This part spins the basket in your appliance by connecting the drive motor to the drive system. You will need to replace the drive belt if your pumps are not spinning, your washer is not agitating, or you are noticing excess noise and/or a burning smell. This belt is black with six ribbings. To replace this part, you will need a Phillips screwdriver.
Fixes these symptoms
  • Burning smell
  • Spinning Issues
  • Spins slowly
  • See more...

Installation Instructions

Phyllis from Brownville, NY
belt was worn and stretched
Place belt on the motor first. Then place belt on pulley on the left side and turn pulley clockwise. Hold belt tight and rotate clockwise. Be careful not to pinch your fingers. Before you buy a belt check your tub first. Grab it in the inside of the front of the tub. If it moves more than a little up and down like an inch or two your tub is shot or the bearings are gone. Found that out later. Check tub first than decide what to do. Read more...
Watch the install video
Water Inlet and Dispenser Valve – Part Number: 134371220
Water Inlet and Dispenser Valve
$58.37
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX1145692
Manufacturer Part Number
134371220
This part comes with the sensor/thermistor.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...

Installation Instructions

rudy from Mercedes, TX
Standing water inside the washers tumbler
An easy repair, this is a blue plastic part that has three solenoids (color coded) when the solenoids wear out, standing water overflow occurs and spills onto your floors. When you get your new part, remove the rear oval cover from the washer so that you can see what your doing, shut the water, disconnect the waterlines and pull the electrical plug. More important pry the top cover upwards from the back, enough to fit your hands, the top cover is held by 2 screws on the back, once you do that you will see the blue plastic part you will be replacing. (you'll need plenty of light) The part is held by 2 Phillips head screws, the one on the right is a little harder to get to. Wiggle the part off and replace with new part. My part didn't come with 2 new black rubber grommets so I used my old ones. The grommets are the most critical parts at this point. if you forget to install em you will have a leak and will have to start over. It took me less than 20 minutes to do this install and I saved about 2 hundred in labor. Read more...
Watch the install video
Front Load Washer Door Lock and Switch Assembly – Part Number: 131763256
Front Load Washer Door Lock and Switch Assembly
$113.22
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12364048
Manufacturer Part Number
131763256
This door lock and switch assembly is an authentic OEM replacement part for your front load washing machine. The lock is used to prevent the door from opening while the machine is running, and the switch indicates that the door is closed, allowing the washer to begin its wash cycle. Attempting to open the washer door while it is still locked can cause damage to these parts. If your washer door will not open, close, or lock, you may need to replace the lock and switch. Please be sure to disconnect the power supply to your washer before beginning this repair.
Fixes these symptoms
  • Leaking
  • Lid or door won’t close
  • Locking Issues
  • See more...

Installation Instructions

Arthur from New Castle, DE
Door would not close/latch.
Removed door from washer. With door on flat surface all the screws are easily removed to replace striker & door hinge/ bushings. Pay attention to bushings position when removing so as to replace them in the same position. Video shows a guy pulling the door gasket off to replace the door lock & switch assembly. Skip that & remove the top cover from the washer. Only two screws in the back hold it on & it's a lot easier to reach inside & pull the switch up than fighting with the door gasket. With the new door hinge, door closes easier & more solid than when brand new. Easy fix. Read more...
Control Knob – Part Number: 131858004
Control Knob
$58.37
In Stock
Fix Number
FIX418888
Manufacturer Part Number
131858004
Sold individually. This white knob accepts a D-shaped shaft.
Fixes these symptoms
  • Touchpad does not respond
  • Will Not Start
  • Won’t Start
  • See more...
Watch the install video
Shock Absorber Kit – Part Number: 5304485917
Shock Absorber Kit
$52.50
In Stock
Fix Number
FIX3508101
Manufacturer Part Number
5304485917
The shock absorber kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin, and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during its cycles. If one or both of them break or wear out it will cause the washer to vibrate or shake and will need to be replaced. This kit is a genuine OEM part. Please remember to disconnect the power to your appliance before starting the repair.
Fixes these symptoms

Installation Instructions

JOSEPH from Olympia, WA
Two busted shock absorbers
The tight confines put a hammer out of the question, so I used needle nose pliers to work the pins out (using leverage against sections in the washer) and then bar clamps to force the new pins in. Bar clamps were critical to the successful installation of these pins given the lack of room I had to work with. Read more...
Watch the install video
Drive V-Belt – Part Number: 134511600
Drive V-Belt
$24.00
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX1146950
Manufacturer Part Number
134511600
If your washer drum is not spinning, there may be an issue with your drive belt. The drive belt wraps around the motor pulley and helps the basket to spin. Other signs there are issues with the belt is if there is a burning rubber smell, or the washer is noisy while spinning. The belt is subjected to wear and tear, and over time it may wear out. This is a genuine OEM part that is made of rubber.
Fixes these symptoms

Installation Instructions

michael from Cave City, KY
browning clothes .zipper on jackets were tore off
after watching video and reading the review, whole job was simple Read more...
Watch the install video
Door Striker – Part Number: 131763302
Door Striker
$36.42
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX2378364
Manufacturer Part Number
131763302
The door striker is a part found on the door of your washer, and it activates the door switch which signals that the door is closed. This genuine OEM replacement part is also known as a door latch or hook, and it is gray in color and made of plastic. You may need to replace the door striker if your washer will not start, or if the door will not open or close. To complete this repair, you will just need a No. 2 square head screwdriver. Open the washer door and remove the screws holding the old striker in place and attach the new one in its place.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

Arthur from New Castle, DE
Door would not close/latch.
Removed door from washer. With door on flat surface all the screws are easily removed to replace striker & door hinge/ bushings. Pay attention to bushings position when removing so as to replace them in the same position. Video shows a guy pulling the door gasket off to replace the door lock & switch assembly. Skip that & remove the top cover from the washer. Only two screws in the back hold it on & it's a lot easier to reach inside & pull the switch up than fighting with the door gasket. With the new door hinge, door closes easier & more solid than when brand new. Easy fix. Read more...
Watch the install video
Single Spring with Insulators – Part Number: 134144700
Single Spring with Insulators
$53.58
In Stock
Fix Number
FIX735645
Manufacturer Part Number
134144700
Fixes these symptoms

Installation Instructions

Michael from sacramento, CA
wash tub hanging low horrible noise while washer was running
one spring was broken and one shock was broken. I used a ratchet strap slung under the tub to raise it enough to install the new springs and used a 1/2" drive socket on the drive end to slip over and release the plastic pins to remove the shocks. pretty easy except that it is all done laying on the floor. I pretty much followed the instructions I found on line. I had to remove lower front panel, rear panel, and top panel to access all this. Also unplug and remove control box. Read more...

Westinghouse Washer Appliance Types

Related Westinghouse Washer Parts

Popular Westinghouse Washer Models

View More
+