MVWB835DC2 Whirlpool - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Delmar from EAST TROY, WI
- Parts Used:
- W11244231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
replaced drain hose that was missing
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from MAYNARDVILLE, TN
- Parts Used:
- W11393685
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer making noise on spin cycle
Removed two screws on back of lid to raise top removed tub one bolt and one spanernut pulled tub lowered top reinstalled screws laid washer down to get to bottom of washer unplugged wiring removed four bolts pulled gear box and motor removed motor from gear box installed motor on new gear box reassemble washer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from BURKBURNETT, TX
- Parts Used:
- W11165546
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer would not fill, all 4 valve solenoid checked good.
The valve is a 4 solenoid valve, which has Temp. sensor molded into the valve body mixer center outlet. No mention of it in the troubleshooting. it has a 2 pin plug. it was shorted zero ohms.
New one measure open infinity. I also purchased the control module as the troubleshooting said to if solenoid checked good which all 4 read 1310 ohms , i purchased and replaced control module, no help. the guide is outdated for these new high tech washers. If this happens again. I will just unplug the 2 pin plug on bottom of valve assembly. By the way the 2 clips that hold the washer top in place are very difficult to remove and re install.
New one measure open infinity. I also purchased the control module as the troubleshooting said to if solenoid checked good which all 4 read 1310 ohms , i purchased and replaced control module, no help. the guide is outdated for these new high tech washers. If this happens again. I will just unplug the 2 pin plug on bottom of valve assembly. By the way the 2 clips that hold the washer top in place are very difficult to remove and re install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from RAVENSDALE, WA
- Parts Used:
- W10902814
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Washer plate stripped where it contacts the drive shaft.
I tilted the washer to access the underside and gently attached the vice grips to keep the drive shaft from turning. I then used my socket set to remove the bolt holding the wash plate in place. I then removed the old wash plate and removed the vice grips before installing the new wash plate. Since the new wash plate engages the shaft (not stripped) I no longer needed the vice grips; it was sufficient to just hold the wash plate with one hand while tightening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Fall City, WA
- Parts Used:
- W11165546
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
I cross threaded the cold water hook up to the washer
If you take the back off the machine, it's a lot easier to detach the control bridge. Saved a lot of time and did not need to stretch your fingers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from MILLBURY, OH
- Parts Used:
- W10752187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Worn out splines connecting transmission driveshaft to agitator.
DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from FAIRBORN, OH
- Parts Used:
- W11165546
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Water Inlet Valve inoperative
Washer would start cycle and return a CL error. No water would flow into the tub. Researched problem and probable cause. Ordered new water inlet valve. Once received, disconnected water hoses and electric plug and removed rear upper access panel (5 screws). Used thin putty knife under sides of front control panel to disengage spring clips. Once access to the faulty valve was attained, removed electrical harness and valve mounting screws. Installation of new valve was reverse process. Figuring out how to raise the front panel for access to the valve was most difficult. Found a YouTube video showing how; it was easy from there. Entire replacement took about 30 mins max.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
Non agitator pulsating action ceased
Ordered the parts and followed You Tube DYI clip. This 3YOMaytag top loading washer has had a motherboard replaced and now this. It all works fine for now, I cannot imagine what the appliance tech would have charged. Maytag is not what it used to be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from INDEPENDENCE, KY
- Parts Used:
- W10752187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
the impellar mechanism wore out so stopped aggitating
Popped the cap , used a socket to unscrew the bolt (it was stripped so ended up having to cut off bolt) Took off old impellar and replaced, installed a new bolt, replaced Cap and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LANCASTER, SC
- Parts Used:
- W10902814
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
washer plate would not agitate
after watching a video i ordered the part. removed the old part and installed the new wash plate using a socket and ratchet.
now washer works like new
now washer works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LeJeanne from BATON ROUGE, LA
- Parts Used:
- W10902814
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Agitator not working: clothes not clean
It was really easy after watching the videio. I removed a single screw and took the agitator out, You could see how worn the center of the part was. The part that it went onto had a lot of rust built up on it, I used naval jelly and a wire brush to clean it. then put the new agitator on. It has been working well ever since. What's crazy is two repair men told me to
throw out the washer because the repair would be equivalent to buying a new one! NOT TRUE ---- Total cost $115.00. Received it really quickly. Thanks so much!
throw out the washer because the repair would be equivalent to buying a new one! NOT TRUE ---- Total cost $115.00. Received it really quickly. Thanks so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from INMAN, SC
- Parts Used:
- WPW10238319
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door alignment
I was sent the wrong part , when I questioned them said they did not have it so was directed to Whirlpool and they are making it and I might get it in May
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!