Models > RA186DCW0

RA186DCW0 Westinghouse Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This motor runs the evaporator fan in your refrigerator. It is mounted on the center hub and has three lead wires terminals. This motor rotates in a clockwise fashion. Its shaft has a diameter of 1/8" and is 1-1/4" long.
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
Sold individually.
In Stock
Order within the next 10 hrs and your part ships today!
This part turns the light on/off as the door opens and closes.
Special Order
This part is found under the refrigerator.
No Longer Available
$10.64
This is used to hold eggs in your refrigerator.
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
No Longer Available
No Longer Available
No Longer Available
Special Order
In Stock
Order within the next 10 hrs and your part ships today!

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for RA186DCW0

Viewing 5 of 5
Noisy
Fixed by these parts
Fixing Fixing
How to fix it
Fridge too warm
Fixed by these parts
Fixing Fixing
How to fix it
Light not working
Fixed by these parts
Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing
How to fix it
Leaking
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jordan from Maumee, OH
Parts Used:
5308000010, 5300158289
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Noisy fan
1. Removed the 7 nuts using the nut driver from the freezer back panel inside the freezer.
2. Remove the back panel. The evaporator motor and fan are located above the coils.
3. Unplug the wiring harness.
4. Remove the two gold mounting screws holding the motor and fan in place.
5. Remove the motor and fan including th e brackets.
6. Install the new motor and fan onto the mounting bracket.
6a. Attach the green ground to the mounting bracket.
7. Screw the two gold screws back into the freezer.
8. Attach the new wiring harness. Note, the old harness had a mounting hole/space for it to connect to the wiring harness of the freezer. The new motor's harness was not long enough for this, so it is connected freely to the freezer harness.
9. Use the hair dryer to melt any ice that may have formed on the coils and hole where the fan goes.
10. Turn the freezer on to see if the fan turns on.
11. Reinstall the back panel.
All done!
152 of 178 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROY from PENSACOLA, FL
Parts Used:
5308000010, 5300158289
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
The Evaporator Fan Burnt Up
The fan motor all but caught the inside of the freezer on fire . Had to remove then clean, and I mean clean the walls of the freezer . Then had to pry out the old fan without breaking anything . Replacement of new fan was quick and easy because all the parts that I needed were in the bag
28 of 38 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Springfield,, TN
Parts Used:
5300158289
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Fan Noise
took cover off inside freezer control . removed old fan and unpluged wire harness plugged new one up and fastened back in place and put control cover back on.
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!