3DWTW4740YQ0 Whirlpool Washer - Instructions

Watched a video on the internet.

Replaced 1 of 4 of the suspension bushing. Works great.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.

Went on u tube saw different video to How disassemble the top to have access to the rod. Changing one by one those rod I was in need of my wife to hold the cover while I was changing the rod.... order for suspension rod kit. Reassemble the top by sliding the cover and to snap. Screw back the panel. And it solve the problem. My wife was really happy so me. It can be done by anybody but first go on the internet to get a idea.

This was a learning experience but it appears to have worked out in the end. Our 3 1/2 year old washer was not agitating much and I attributed that to a loose bolt. I would tighten the bolt and it would work ok for a load or two and then stop agitating. I would find that the bolt was loose again. I took a number of steps to try to get the bolt to stay on tight - threadlock, a new bolt, more threadlock, and applying progressively more force on the bolt, with no better results. Yet the repair guys on you tube were saying the bolt only needs to be snug, not super tight - something was amiss. I even went so far as to secure the basket with a rope so I could use two hands on the socket wrench (please don't do this). But when I tried the washer again there was no agitation at all! I observed the agitation output in manual test mode and the bolt was turning in lock step with the shaft but the agitator wasn't turning at all. That's when I suspected that the problem was actually a worn lower agitator. Trouble was that now I couldn't seem to get the bolt off. Turning the wrench caused the shaft itself to rotate so I couldn't loosen the bolt from the shaft. I thought I broke the washer. Then I considered that maybe the shaft was rotating because the washer was in an agitation mode when I turned it off. I went back into manual test mode, made the washer spin, then turned it off. Fortunately, this worked. The shaft was again stationary and, albeit with great difficulty, I got the bolt off.

I removed the agitator, and as a pro would have figured out long before, the ridges inside the top of the lower agitator were almost completely worn down. I realized then that the contact between these ridges and the splines on the shaft is what is supposed to cause the lower agitator to move with the shaft. The purpose of the bolt is just to keep the agitator in the correct position and from coming off the shaft. I had been trying to compensate for the worn agitator ridges by over-tightening the bolt, creating some contact at the top of the shaft. This would work for a little while, then the agitator would start slipping, and the slipping agitator was acting just like a wrench loosening the bolt (until my stupid rope trick, that is.)

So I ordered a new agitator (only the lower agitator was bad, but the price of an entire agitator isn't a lot more than just the lower part and I was reading that the upper agitator parts will wear over time) and another new bolt (because my repeated attempts to over-tighten the first one I ordered had split the rubber gasket apart and worn the bolt head).

The new agitator fit snugly on the splines of the shaft so I sensed no need to use excessive force on the bolt. Just an easy one-handed snug tightening with the socket wrench, using the other hand to hold the lower agitator. The washer is now working again.

watch utube instruction.easy repair

slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...

I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.

Machine works great now.

I watched a video on you tube before making the repair, there was only one bad rod support, location right rear, I recommend watching a video on you tube first, it is very simple to change, however the replacement of the part was not the solution to the unbalanced load during the spin cycle, so I guess I have some research to do.

The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you

Per instruction sent with purchase

Remove top of washer suspension
Rod goes on side of tub .