Models
>
LFA6900G0
LFA6900G0 Whirlpool Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$22.91
This lid or door switch kit helps ensure your washer or dryer only runs when the door is properly closed. It’s a safety feature that prevents spills and keeps your appliance working as it should. The ...
In Stock
Order now and your part arrives by Apr 6
This drive block connects the spin basket to the drive shaft in large-capacity washers, allowing proper spinning during cycles. At 2-5/16 inches high, it’s easy to install with basic tools. Replace if...
In Stock
Order now and your part arrives by Apr 6
This valve has two ports for water to enter. This valve is compatible with a half inch ID hose and it has two 3/4-11x1/2 NHT hose threads.
No Longer Available
$98.25
This pump is used for washing machines that do not have a lint filter and do not automatically clean out the excess built up lint.
***NOTE: This part may appear different, but will function the same as the original.
Special Order
In Stock
Order now and your part arrives by Apr 6
This two-speed motor performs 1725 revolutions per minute in one speed, and 1140 revolutions per minute in the other speed. It runs at 1/2 horsepower and carries 115 volts.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for LFA6900G0
Viewing 7 of 7Will Not Start
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Wilmington, IL
- Parts Used:
- W10820036
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Lid closes, switch wouldn't turn on machine.
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams.
... Read more
Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from Plano, TX
- Parts Used:
- W10820036
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer would fill up, wash, then stop
I deduced the lid switch was the problem.
I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed ... Read more it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.
The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.
I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed ... Read more it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.
The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Homosassa, FL
- Parts Used:
- 350365
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
water pump
replaced
Was this instruction helpful to you?
Thank you for voting!