SWT120WN Speed Queen Washer - Instructions

Biggest trick is getting the agitator off. It seems like it is bolted on. I used a piece of braided cotton cord to run under both sides of the agitator and just pulled real hard. It WILL pop off.

Next the old seal will also seem to be attached. The edge is firm but not bolted. A small prybar will help.

Easy repair to do, but it did not fix my problem. I decided to get a new washer rather than go through further disassembly.

I had some sweaking and then burning followed. I came to find the belt had burnt and stopped my washer from working. Ordered a belt and replaced. Washer worked for one week. Squeaking and burning again. Belt was still intact, thank goodness. Beleive it is another pulley part for the washer. Might order another part. Overall the fix was good, but had another issue.

1) removed front panels from washing machine
2) removed water pump. Three small torque bit screws and (2) hoses.
3) removed motor (because I realized that the belt tensioner also needed work as it was siezed) removed (4) bolts and an electical connector.
4) repaired tensioner by taking apart and cleaning bearing surface. Needed snap ring plyers to take apart.
5) put motor back in
6) replaced belt
7) put water pump back on
8) intalled front panels back on washer

remove agitator then remove center bolt from hub, match bolt with longer bolt so that gear puller will work. install bolt and gear puller and twist top of gear puller until hub is removed. remove old seal ,use sand cloth or emery cloth to remove all deposits from shoulder. make it shinny, use some dawn dishwashing soap to line the inside of the new seal at the bottom and slide into place.take a piece of 2" PVC about 4" long and slide over the top of the seal and tap with a rubber hammer until seal is seated firmly on shoulder. look to see that there are no gaps with a inspection mirror or a make-up mirror.If their are no gaps ,install the hub and tap on the new hub with the rubber hammer. the hub will not seat all the way down so use the old bolt to pull it down, now take out the old bolt and install the new one, this is because the new one has lock tite on it ,your done!

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

After turning on the machine set to the spin cycle and acertaining that the problem was not a switch or the motor the lower cover was removed (Two sheet metal hex head screws)with appropriate socket. The failure of the belt was self-evident, having sprayed itself in granuals, the belt itself having parted with easy removal.
A search of the internet produced the order for drive belt, which arrived in a timely manner trough Fedex.

Replacing the belt was the most labor intensive part of the process. No mirror being available a CD was placed in the base of the machine in order to view what fasteners (Three torx head) fasened the pump to the motor assembly. Removal of the pump was necessary in order to replace the belt.

The removal of the fasteners required that three holes (120* angular spacing, 1/2" diameter, located on the pump fastener bosses) be drilled in the machine base in order to
remove and replace. This required setting the machine on its side. (Tell the engineers to put an inspection plate there in order to negate having to drill the holes. Thankx.) Pump assembly was lowered off driveshaft and belt replaced. Tensioner set on belt after pump assembly fit to driveshaft and torx fasteners replaced and tightened. Machine powered up, checked for function. In use. Lower cover replaced. I'll be using your buisness for parts again, no doubt.

Screw broke lose in agitator from drive bell stripped (plastic) for transmission gear. Received new Drive Bell and had to lightly cut out old from Agitator housing with saws all, cleaned years of soap build up on steel spline with wire grinder, lubed the Drive Bell inter and pounded on to spline gear with rubber mallet, I thought a bit too much force but what the heck I landed to the same bearing point as before. Work Out Great.

Followed video on PartsSelect website, they made it real easy.

Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.

Found out that these switches go from time to time and are usually the culprit when the washer won't operate. Opened the cabinet facing. Warning: there are plenty of YouTube videos on opening Maytag washers. None helped me with this model. I ended up finding the screws to open near the floor on front. Once it's opened, just replace the faulty switch, reconnect and you're in business. Getting the washer opened was about the hardest part of this repair. Total cost: Less than $30.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

Since the agitator and bell housing seperated as once piece from the drive shaft I didn't have to remove them and the schematic showed how the agitator snapped on to the bell housing and the parts I needed for the fix. The new seal went on with no problem, I just used some of the supplied grease on the tight spots. The hardest part was attaching the bell housing. It came to within an inch of the top of the shaft with no problem with a rubber hammer. But the top screw shroud broke when I tried to hammer it the rest of the way using a wood dowel and a block of wood. I couldn't even get the threads of the supplied screw to even touch the drive shaft. So I bought a longer (1 inch) cap screw from the hardware store and added a washer and suplied ring. After torqing it to 5 ft-lbs instead of the 10-20 the plastic beneath the screw was looking kind of thin and stressed and I was afraid of it breaking through or the screw snapping off in the shaft, so I left it alone and used some silicone caulk to seal in the plug that goes in on top of the screw since the side of the shroud broke off. I slipped on the agitator and am testing a load now as we speak. If I get ten more years out of the washer it will definitely be worth the $100 in parts and shipping !

I opened the bottom and found the belt had broke in half. i ordered a new belt from Maytag online and found a you tube video that showed exactle how to change it. the only thing i had to do afterwards was tighten the tensioner.eazy pezy!