WFJ1254 Samsung Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from Peachtree City, GA
- Parts Used:
- DC62-30312J
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
OE error code, water keeps flowing during spin cycle, softener dispenser left half full of water, clothes wet after washer stops
Found a repair video of a Samsung washer that looks like mine (9 years old). Removed two screws from the back of the washer, slid the top a few inches toward the front and lifted it off. Disconnected the two double electrical connections, the two rubber tubes from the solenoids, the cold water hose from the back and removed the two screws holding the valve in place. Installed the new valve by reversing those steps, slid the top back into place and secured it with the two screws and viola (as Kelly Bundy would say)! The washer now functions normally. I'm waiting for my next water bill to arrive to see whether the sudden increase in usage decreases to its normal amount. We have three adults and four small children in the household so the washer is constantly in use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from MYRTLE BEACH, SC
- Parts Used:
- DC97-09760A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door latch broke
Still have not received my part, been nine days since I ordered it. It was in a warehouse 600 miles from my house, as now travel over 3000 Thanks fed ex
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Leesburg, FL
- Parts Used:
- DC67-00244A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The drain hose disappeared.
The new hose arrived without a plug, so I found a golf tee that fit securely.
I put a few drops of dish soap on the machine end and it slid on with a little resistance.
I ran a few light cycles, and the leak has stopped.
Thank you
I put a few drops of dish soap on the machine end and it slid on with a little resistance.
I ran a few light cycles, and the leak has stopped.
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from NEEDVILLE, TX
- Parts Used:
- DC60-40137A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
Washer making noise a snow smoking.
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.
Was this instruction helpful to you?
Thank you for voting!