CA106S Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from New Orleans, LA
- Parts Used:
- WP211726
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washing machine lid came off during a move
First, I secured one lid hinge ball in its appropriate position between the lid and the washer. While keeping the first ball in place I placed the other lid hinge ball as close to its intended position as I could get it. Next, I pushed the lid and ball into its position.
Was this instruction helpful to you?
Thank you for voting!
Stripped leveler screw making impossible to level my washer
Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra L from Warren, OH
- Parts Used:
- WP211726
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Washing machine lid hinge balls fell off machine lid
First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixed to your machine where you can lift the lid and it will stay up without falling.
Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.
Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EL from O'Fallon, IL
- Parts Used:
- WP211726
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Resin balls on which the top loader lid hinges had broken.
Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from SEDONA, AZ
- Parts Used:
- 22003428
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Threads on old legs had been damaged in moving to new location.
Removed the damaged legs, replaced with parts from this site and leveled the washer .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from MOUNTAIN BRK, AL
- Parts Used:
- WP212716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer is 27 years old. The washer lid bumpers were just worn out with age. It has been in constant use all these years raising 4 children with no other service or repairs. It has a matching dryer with the same track record. What a testament!
Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michell from TOOMSUBA, MS
- Parts Used:
- WP211726
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing hinge lid ball
Used duct tape as the video provided instructed and also to hold second hinge lid ball in place. Firmly pushed down on the lid until it easily popped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Pacific Palisades, CA
- Parts Used:
- WP212716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing machine lid kept banging shut and rattled when the clothes were being washed.
I was only missing one of the bumpers but that was in pretty poor shape so I replaced them both. It didn't take much to do. Just pressed the bumper into place and Viola! instant gratification.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from The Woodlands, TX
- Parts Used:
- 22003428
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Leg was mssing after move into new home.
Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.
Was this instruction helpful to you?
Thank you for voting!