Models
>
CA106
CA106 Maytag Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CA106
Viewing 17 of 17
Keep searches simple, eg. "belt" or "pump".
$11.98
This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers.
In Stock
Order now and your part arrives by Apr 9
This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Ma...
In Stock
Order now and your part arrives by Apr 9
$9.79
This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.
In Stock
Order now and your part arrives by Apr 9
$7.60
This washing machine lid bumper is just under an inch long. It is all gray in color and is made entirely of rubber.
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
Special Order
Special Order
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for CA106
Viewing 2 of 2Lid or door won’t close
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from New Orleans, LA
- Parts Used:
- WP211726
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washing machine lid came off during a move
First, I secured one lid hinge ball in its appropriate position between the lid and the washer. While keeping the first ball in place I placed the other lid hinge ball as close to its intended position as I could get it. Next, I pushed the lid and ball into its position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra L from Warren, OH
- Parts Used:
- WP211726
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Washing machine lid hinge balls fell off machine lid
First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixe
... Read more
d to your machine where you can lift the lid and it will stay up without falling.
Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.
Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EL from O'Fallon, IL
- Parts Used:
- WP211726
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Resin balls on which the top loader lid hinges had broken.
Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, beg
... Read more
an pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.
Read less
Was this instruction helpful to you?
Thank you for voting!