HA606 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Woodside, CA
- Parts Used:
- WP22001619
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
water kept filling until overflow
removed back of control panel to find that a mouse chewed the air tube. tried to splice it with a barb connector, it did not work. Ordered part received it 2 days later and installed it. I would recommend buying parts from these folks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Coal Valley, IL
- Parts Used:
- 204968
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The plunger was worn down. Washer would shut off during the washing cycle.
I started by unplugging the washing machine from the wall outlet. I then proceded to remove four screws from the top of the control panel. After removing the screws I put two flat head screwdrivers on each side of the lid and applied force to pry the lid from the ball joints holding it in place. This was the part that was the most difficult in my opinion. After the lid was off, I removed the bolt that was holding the fuse switch in place and removed that from the slots. Next I unscrewed the two screws on opposite sides of the switch head where it makes the contact with the lid. This allows you to remove the switch assembly out of the unit. Once the assembly was out, I assembled pieced the new parts together by looking at the old parts. Then, I placed the new assembly back in the unit. Be careful when you put in the new assembly that you test the switch and make sure you hear the "Click" from the switch. After that I reversed all the steps and put the unit back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from GALLUP, NM
- Parts Used:
- WP22001619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Washer wouldn't stop filling with water.
It should have been extremely easy, but it was a little difficult because my laundry room is very small and I had extremely limited space to work in and also had limited lighting. However, after taking many minutes to strategically plan how to maneuver in the tiny space, I was able to loosen the giant clamp on the hose inside the washer and attach the new hose! It worked like a charm! My 25 year old Maytag is working again! The part came in a bag certified as a genuine Whirlpool part and looked exactly like the old one! No complaints! The online installation videos are wonderful!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from SMITHFIELD, KY
- Parts Used:
- WP22001619
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Washer was overfilling from water level selected
Tried the water level control first. didn't fix it.
Then replaced the air tube for tub fill volume.
The thing here is that it didn't have a hole in it nor was it blocked where you couldn't blow through it.
The prolbem was that at the tub end it has a larger diameter and that was nearly filled with softener residue so it changed the air volume.
That reduced air volume caused the air pressure to be wrong to the water level sensor.
My most useful tool was a magnet mount flashligt inside the cabinet so I could see to get the hose back on.
Then replaced the air tube for tub fill volume.
The thing here is that it didn't have a hole in it nor was it blocked where you couldn't blow through it.
The prolbem was that at the tub end it has a larger diameter and that was nearly filled with softener residue so it changed the air volume.
That reduced air volume caused the air pressure to be wrong to the water level sensor.
My most useful tool was a magnet mount flashligt inside the cabinet so I could see to get the hose back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from OSWEGO, NY
- Parts Used:
- WP22001619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Washer would not stop filling water
Replaced the air tube, existing one had been chewed by mice was easy to replace and solved the issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Brambleton, VA
- Parts Used:
- WP213720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Small spring in the lid switch broke
I removed the two screws holding the switch and removed it from the machine. I then removed the broken spring and replaced it with the new one sent to me from partselect.com. I reinstalled the repaired switch and turned on the machine. It was easy as that and it works great. PartSelect.com is the best.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Philadelphia, AL
- Parts Used:
- 214196, WPW10137328, WP211065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
timner knob stopped catching
Lost Timer knob retaining clip & spring when I removed it before ordering. Put spring on, then knob then retaining clip. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from Mill Spring, NC
- Parts Used:
- WP213720
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing Machine wouldn't agitate
First I removed the front of the washing machine and removed the two bolts that held the top in place. I then replaced the spring. The spring was a little tricky because I had to use a screwdriver to stretch the spring enough to fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Macungie, PA
- Parts Used:
- WP213720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Machine stopped running.
Actuator spring for the lid switch broke. Removed the lid by prying it from the top of the machine. The lid is secured by two plastic balls on either side. Removed the actuator switch screws and slid the actuator assembly out over the washer drum. Replaced the spring and reassembled the actuator to the machine. Put vaseline on each plastic ball to hold them in place while I snapped the lid back on to the machine top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Fallston, MD
- Parts Used:
- WP22001619
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washtub overflowing
Removed access panel on back of machine to remove Air Tube where it connects to wash basin. Removed control panel cover on top of machine and front panel of machine so top could be lifted for easier access to the point where Air Tube plugs in to water level selector switch. Tube is attached at both ends via spring clips. Replaced tube; problem solved. As a note, the old tube was clogged, and once cleaned, the machine functioned normally again. I had already ordered the replacement so I installed it in place of the old tube when it arrived. The new tube is significantly longer but functions perfectly.
Was this instruction helpful to you?
Thank you for voting!