7MMVWB950AG0 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from PERKINS, GA
- Parts Used:
- W10440729
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Washer was off balance during spin cycle. The suspension piece broken.
Replaced 1 of 4 of the suspension bushing. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from CLARK, MO
- Parts Used:
- W10820039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The washer was making a horrible noise during the spin cycle
Removed a cap in the center of the tub basket which has a bolt that needs removed I believe it's a 9/16 after I removed the bolt I then removed the center of the bottom of the basket assembly which then allowed me to get to the basket hub that needed replaced it was a little dirty and I couldn't get it out so I sprayed a little penitrating oil on it let it sit a little then I was able to remove the hub and install the new one then I put it all back together and the washer is working great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from YORK, PA
- Parts Used:
- W10820039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Washer would vibrate and bang viciously in the spin cycles
Remove agitator and replace hub. I also recommend replacing the Suspension too. I could tell the hub was bad the piece of metal washer on the bottom was gone. The suspension lost a lot of its stiffing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from SAYRE, PA
- Parts Used:
- WPW10619844
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Lid Lock broke
Followed video from you tube. Man made it look very easy. Not! Hole that lock has to come through in back was very tricky. Also, DO NOT THROW OUT OLD PART UNTIL NEW ONE IS INSTALLED. The reason for that is there is a CLIP at the end of the old part that is needed to attach new part to wire section in control panel. NO WHERE is it mentioned at you got the clip from the old part. Luckily we saved it. Without that clip, you are screwed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dyleena from HOUSTON, TX
- Parts Used:
- WPW10619844
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer would not start due to lock mechanism turning on and off.
Dismantled washer lid to install new locking mechanism.
Was this instruction helpful to you?
Thank you for voting!
my daughters ferret chewed little pinholes in the pump hoses
two small compression clamps hold the hoses in place. these are very simple to remove, however to reinstall the new hoses you should unscrew the pumps with a nut driver, secure the hoses with the clamps, and then screw the pump back to the bottom of the drum. oh yeah make sure to put the back plate back on the machine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MORGANTON, GA
- Parts Used:
- W10820039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Unlevel code. Would not complete spin cycle.
First replaced four basket spring supports. Next tried Basket hub assembly ( which showed wear, but not total solution). Next replaced the rotation sensor that's on the stator. That finalized the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from WALFORD, IA
- Parts Used:
- W10820039
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Error reading 5D - wouldn't spin
3rd time replacing this part. The plastic grooves against the metal get wore down. Only 20$ to repair ! Take off the 3/8 bolt - center pops out. Remove screws pop out old piece and tighten new piece each side evenly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from NORTH OLMSTED, OH
- Parts Used:
- W10440729
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer is unbalanced during a spin cycle
I watched a video on you tube before making the repair, there was only one bad rod support, location right rear, I recommend watching a video on you tube first, it is very simple to change, however the replacement of the part was not the solution to the unbalanced load during the spin cycle, so I guess I have some research to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from FLINT HILL, VA
- Parts Used:
- W10853723
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Cold water leaked into tub
Replaced water inlet valve. Parts select video was incorrect for my unit. There are no spring clips to be released using a putty knife. Rather remove the two screws in the back of the top, pull the top forward and up to get at hose connections to the valve. Hint, place a towel under the valve connections because after removed from the valve, the hoses will leak to the floor. I propped the top up with a stick. All the other stuff in the video is good. Unplug and turn water off, remove connectors from old valve etc. . I also removed the protective plate over the cabled that runs between the washer and the control panel located on the back of the washer. The will make the sliding of the top forward easier. Only one screw involved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from HOUSTON, TX
- Parts Used:
- W10820039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Whirlpool cabrio would not go into the spin function without triggering an error code of 5d
Removed the center cover of the agitator with a flathead. Removed the nut of the agitator main cover. Had trouble taking the cover off because of the crud holding it down I wiggled it up gently alternating n,s and e,w until I eventually saw it separating from the bottom of the basket. Once it came off you could see how nasty the old hub assembly looked. Took the screws off the old hub assembly and removed it. Matched it up with the correct new hub assembly cause the kit comes with 2. Cleaned the shaft and that general area. Installed the new hub assembly, replaced the covers. Ran the drain and spin cycle and it worked with no problem. There are videos on YouTube that show you too. DO NOT try to pry the agitator cover if it won’t rise up easily. Be patient and it will come out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SAVANNAH, MO
- Parts Used:
- W10820039
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Washer making lot of noise during spin cycles
Removed agitator and basket hub parts and cleaned all parts of agitator then replace basket hub with new basket hub kit according to video ran washer but did not solve problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edgardo from SALEM, OR
- Parts Used:
- WPW10178988
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
F51 error code
Pretty easy! Just follow this link on how to fix the problem:
https://www.youtube.com/watch?v=_-Hg8rLGiKQ
The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be.
https://www.youtube.com/watch?v=_-Hg8rLGiKQ
The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be.
Was this instruction helpful to you?
Thank you for voting!