HA3000W ((POST.C348C774)) Magic Chef Washer - Instructions

VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, remove 4 mounting bracket screws that secure the motor and pump assembly. Pull back the tension/idler pulley to loosen belt off the main pulley to the washer drum. Tilt and pull out motor/pump assembly. Underneath the pump, use star-bit to remove the pump from motor assembly to remove the belt. Install new belt on motor pulley (Good time to check for debris or anything restricing free movement of pump) and re-install pump. Install the motor/pump assembly and loosely secure the motor/pump assembly. Place the belt onto the motor pulley and pull back the tensioner/idler pulley to allow slack of belt to be placed on washer drum pulley. Put the belt on the lip of the drum pulley and rotate while pulling back the tensioner/idler pulley until the belt is seated on the groove of the drum pulley. Tighten the motor/pump assembley. Re-attach the 2 hoses and tighten down the clamps. Re-connect the electrical connector to the motor...Don't forget to plug in the washer and secure the front panel...Piece 'O cake, you're done! About 15 minutes to do the job. Much like changing a belt on most vehicles.

This was my fist time attempting to fix a washer. I had to guess on the length of the belt since the model number on the machine had worn off and the belt had snapped in a way that made determining the length difficult. At first, I ordered a belt that was too small. I realized this after I was unable to remount the motor stand onto the bottom of the machine. This model had the motor assembly right in front of the unit. It was easily accessed after removing the panel on the front of the machine. It was easy to remove the 4 screws (they were all visible) on the motor stand. After that I was able to disconnect the pump belt. This machine has seperate belts for agitation and the pump. The pump belt must be removed in order to install the agitator belt because they both are driven by the same shaft and the pump belt is positioned on the bottom. There is also a tension wheel for the agitator belt which might be easily overlooked. Make sure to install the agitator belt so that the tension wheel is on the outside of the belt's path. The whole job is fairly easy if you have the right part to begin with. If you have to force the belt onto the wheels, then you probably have a belt that is too small.

The only real problem was one spring loaded hose clamp to the rear of the pump. If it had been a standard clamp like the others I would have cut the repair time down by 2/3rd's. I did find that by removing one of the long wash drum springs, I then had more room to get my channellocks back there to get the stupid clamp to compress, and then used a screw driver to push the clamp back off the the connecting port. I replaced the camp w/ a standard clamp and the reassembly went quick and easy. Note, If you replace the pump drive belt with a new one, you WILL have to adjust the belt tension after a few minutes use.

Released idler pulley and replaced belt

took the drive belt to the pump off then put the belt for the drum on .then put the belt for pump back on. basickly this unit is one of the easist to work on

It was easy, All we had to do was loosen up the tension on the pump, put the new belt back on and put the tension back on the pump motor by sliding it to the side and re tighten the screws to hold the pump tight.

Un plug machine. Turn off hot & cold water. Remove the front panel by removing the 2 screws at the botton & lift front from the bottom until it unhinges from the top. Tilt the washer back far enough to put a contaner to catch the water left in the hoses. Loosing the hose clamps so the water comes out slowly. If you remove the hose to fast your container won't catch the water. Do one hose at a time. Next disconnect the wiring harnes from the motor. Remove the 4 screws holding the pump/motor. Disconnect the belt from the washer. You will have to tilt the pump/motor to get slack in the belt. Remove the pump/motor & the belt will come with it. This is when I found that the belt was toast & I had to order a belt. Paid shipping twice. once for pump & once for belt. Seperate pump from motor by removing 3 screws. My pump came right off. Reverse the operation to install. REMEMBER TO PUT THE BELT ON BEFORE THE PUMP.

Removed the old pump and installed the new one, works great!

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

Turned off water & unpluged ac power. Removed 2 screws on front panel. Removed panel. Found peices of V belt. Removed 4 screws from electric motor which allowed the belt to come out. Ordered new belt on line. Received the item in one day. Reversed the above sequence above. Now the washer is running as good as new.

First thing I did was to read the great information from other customers. John from Milton's post titled "frayed v belt" was excellent; so was Joseph from Goldsboro NC under the Pump part posts. I would add the following info which wasn't readily available. The Torx/starbit size mentioned in the posts referenced is a T25 the Amana lw8203w2 I have. I bought a t25 size torx wrench at my local hardware store for $2. I got everything together --the belt took some arm strength for an amateur like me to get on. Also, would recommend gloves as some of the edges are sharp down there. Everything appeared okay and when I started the spin cycle it started then cut off. I thought maybe besides the fan belt there was electronics faulty. However, I found an amana repair guide for my model online at scribd and under the troubleshooting section, it described the cutout of the spin cycle and if the new fan belt is too tight, it will bind and the spin cycle will cut out. So I opened up the front again and worked the belt for several turns to "stretch it" and voila, it worked perfectly.