Models > WM3431HW

WM3431HW LG Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Models for WM3431HW

Diagrams for WM3431HW

Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it ...
In Stock
Order now and your part arrives by Nov 22
Regulate the washer?s hot water supply with this single-solenoid inlet valve. It links the household hot water line to the internal filling system, opening on a control request and closing when the fi...
In Stock
Order now and your part arrives by Nov 22
A rubber barrier around the rotating drum shaft helps protect the washer?s tub bearings from water and detergent. This rear tub shaft seal sits in the rear outer tub, keeping wash water out of the bea...
In Stock
Order now and your part arrives by Nov 22
On Order
No Longer Available
$26.19
The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.
Special Order
Sold individually.
In Stock
Order now and your part arrives by Nov 22
$16.45
This hose clamp applies pressure around the hose end, holding it firmly against its fitting during operation. A secure hose connection helps keep water contained inside the appliance. This OEM part is...
In Stock
Order now and your part arrives by Nov 22
This thermistor sensor changes electrical resistance as temperature changes, sending a reading to the main control board so it can manage heat as needed. Accurate temperature feedback helps the applia...
In Stock
Order now and your part arrives by Nov 22
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before be...
No Longer Available
In Stock
Order now and your part arrives by Nov 22
In Stock
Order now and your part arrives by Nov 22

Common Problems and Symptoms for WM3431HW

Viewing 12 of 12
Will not drain
Fixed by these parts
Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Draining Issues
Fixed by these parts
Fixing
How to fix it
Water Filling Issues
Fixed by these parts
Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Engine runs but does not pump water
Fixed by these parts
Fixing
How to fix it
No hot or cold water
Fixed by these parts
Fixing
How to fix it
Spinning Issues
Fixed by these parts
Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
Fixing
How to fix it
Noisy
Fixed by these parts
Fixing
How to fix it
Not draining
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jorge from Apple Valley, CA
Parts Used:
4681EA2001T
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
592 of 761 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from RALEIGH, NC
Parts Used:
4681EA2001T
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
noisy operation, sometimes did not drain, gave OE code
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
60 of 81 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from COTTAGE GROVE, WI
Parts Used:
4681EA2001T
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Pump rotor broke off shaft.
There are two pumps in this system. I turned the washer on its side and took off bottom plate. There are several screws holding this on. I then took the entire pump assembly off. There are 3 screws holding each pump on the brown plastic body. Each pump has a positive and negative lead. I switched out the pump and reassembled. The h ardest part is getting the 3 "shock absorbers in place with the rubber sleeves. I think the book suggest getting to the pump from the front side but I went through the bottom. Worked good. I did wonder however if the other pump was working. Do you need two pump working to get flow? By replacing one pump I went from no flow to good flow. Cost me $75.00
23 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!