Models
>
WT7150CW
WT7150CW (ABWETUS) LG Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WT7150CW
Viewing 3 of 3Keep searches simple, eg. "belt" or "pump".
$49.45
Clothing moves over a covered mounting point with help from this washer pulsator cap. The round plastic cover snaps into the center of the washplate, concealing the mounting bolt and providing a smoot...
In Stock
Order now and your part arrives by Nov 23
$202.55
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If...
In Stock
Order now and your part arrives by Nov 23
$32.95
Restore a washer component?s fastening point with this replacement screw when the original is missing, stripped, or damaged. Secure fastening helps parts stay firmly attached during operation. A worn ...
In Stock
Order now and your part arrives by Nov 23
This pressure sensor assembly measures changes in air pressure through a connected tube as water enters or leaves the tub. Accurate water level sensing helps the washer fill and advance through its cy...
In Stock
Order now and your part arrives by Nov 23
$154.80
This lid switch and lock assembly keeps the washer lid secure during operation. It detects whether the lid is closed and sends that information to the main control board. This is an OEM replacement ob...
In Stock
Order now and your part arrives by Nov 23
In Stock
Order now and your part arrives by Nov 23
$44.99
Transfer rotation between adjoining washer drive components with this agitator coupling. Its shaped contact surfaces engage the connected parts so they can move together under load during washing and ...
In Stock
Order now and your part arrives by Nov 23
$142.60
This washer inlet valve assembly is responsible for regulating the flow of both hot and cold water into your washing machine. It opens and closes at specific points during the wash cycle to ensure the...
In Stock
Order now and your part arrives by Nov 23
On Order
In Stock
Order now and your part arrives by Nov 23
$62.65
Maintain a watertight seal and prevent leaks with this genuine bellows assembly, designed for LG front-load washers. Also known as a door boot bellow or tub-to-pump hose, this flexible rubber gasket c...
In Stock
Order now and your part arrives by Nov 23
In Stock
Order now and your part arrives by Nov 23
Common Problems and Symptoms for WT7150CW
Viewing 8 of 8Will not agitate
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deresa from BOLINGBROOK, IL
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The bolt in pulsator kept coming out during the wash
I found the pulsator just spun freely, I determined the hole on underside should ribbed to align with the ribbed shaft. But it was wore away. I purchased the new part and replacement was simple. It slide right on and I replaced the bolt. Pulsator works great, washing again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from JASPER, MO
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Agitator was free spinning
Removed the center cover cap carefully on top of the agitator with a small screw driver. There are 3 (on mine) little slots around the edge of the bottom of the cap where it meets the agitator. Insert the small flat blade screwdriver and gently twist at each one till the cap pops loose and comes off.
There was a 10MM bolt under ... Read more the cap on mine that you need to remove. I used an cordless impact driver but you could use a socket wrench as well. Remove the bolt and the agitator comes off. May take a little wiggling or it may come right off.
The teeth on the agitator were wore all the way down and gone on mine so it came off easy and this was the issue I had why it was spinning freely. I took the small flat blade screwdriver and used the edge and corner of the blade to clean the teeth on the shaft where the agitator attaches and wiped it down before installing the new part as there was quite a bit of metal shavings from the damaged part.
I just reversed the order of removal to install the new part. Took about 15 min. I ran a rinse and spin cycle to remove any additional metal shavings and to check to see if it all worked properly. THATS IT! TOO EASY!
There was a 10MM bolt under ... Read more the cap on mine that you need to remove. I used an cordless impact driver but you could use a socket wrench as well. Remove the bolt and the agitator comes off. May take a little wiggling or it may come right off.
The teeth on the agitator were wore all the way down and gone on mine so it came off easy and this was the issue I had why it was spinning freely. I took the small flat blade screwdriver and used the edge and corner of the blade to clean the teeth on the shaft where the agitator attaches and wiped it down before installing the new part as there was quite a bit of metal shavings from the damaged part.
I just reversed the order of removal to install the new part. Took about 15 min. I ran a rinse and spin cycle to remove any additional metal shavings and to check to see if it all worked properly. THATS IT! TOO EASY!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from FT WORTH, TX
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Pulsator stripped out
The teeth in the pulsator assembly where stripped out on the original plate.
Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair
Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair
Was this instruction helpful to you?
Thank you for voting!