T1872EFHSTD (ABLETUS) LG Washer - Instructions

Disconnect machine from power source. Then, disconnect any tubes from the back side (make sure you close any water valves before doing so). Then, lay the machine on its back to access the bottom of the machine. Then, locate the thermistor and replace it with the new one (the thermistor will have two screws holding it in place, simply remove the screws and replace the thermistor, then screw it back in). After the new part is installed, stand the machine back up and make sure to connect any tubing to its proper place. Done.

Removed the center cover cap carefully on top of the agitator with a small screw driver. There are 3 (on mine) little slots around the edge of the bottom of the cap where it meets the agitator. Insert the small flat blade screwdriver and gently twist at each one till the cap pops loose and comes off.

There was a 10MM bolt under the cap on mine that you need to remove. I used an cordless impact driver but you could use a socket wrench as well. Remove the bolt and the agitator comes off. May take a little wiggling or it may come right off.

The teeth on the agitator were wore all the way down and gone on mine so it came off easy and this was the issue I had why it was spinning freely. I took the small flat blade screwdriver and used the edge and corner of the blade to clean the teeth on the shaft where the agitator attaches and wiped it down before installing the new part as there was quite a bit of metal shavings from the damaged part.

I just reversed the order of removal to install the new part. Took about 15 min. I ran a rinse and spin cycle to remove any additional metal shavings and to check to see if it all worked properly. THATS IT! TOO EASY!

I found the pulsator just spun freely, I determined the hole on underside should ribbed to align with the ribbed shaft. But it was wore away. I purchased the new part and replacement was simple. It slide right on and I replaced the bolt. Pulsator works great, washing again.

The teeth in the pulsator assembly where stripped out on the original plate.

Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair

I had a hard time removing the agitator, had to get thin prybar to get a hold of washplate. After I removed washplate, I found that the shaft that the washplate attaches to was actually worn out. What used to be a spline was smooth. So I ordered a new clutch assembly. There are a lot of bolts that hold the clutch assembly on to the basket. There are a lot of videos on Utube that will walk you through step by step. The only problem I encountered with this was removing the nut that holds the basket to the tub. One video said it was reverse thread, which it wasn’t. You can check the thread on new clutch assembly to see which way is correct. After I put back together. Works like new.

Our Samsung HE washer started making a grinding noise and stopping at the end of the rinse/spin cycle. I had replaced the clutch and seal 2 years ago and it sounded like it was going out again, however we were not getting the gunk inside the tub like before (seal) and the machine was throwing the tE error code when it stopped which it did not do last time. According to the manual this meant a thermistor error and the solution was "Call for Service". The machine is 9 years old and way out of warranty so....uh No! I ordered the new thermistor for $15 plus shipping to correct the tE code before looking to replace the clutch again or get a new machine. The new thermistor arrived, leaned the machine on its back, unplug one connector, remove two screws and pull the old one out of it's hole, push the new one in, replace two screws and the connector and GO! Problem fixed! No tE code, no stopping, no grinding noise. As best I can tell, the old thermistor was faulting during the spin cycle and the machine went into emergency stop mode which made the grinding noise. It was not the clutch or bearing at all. Most of the repair time was moving the machine out and disconnecting lines so I could lean it onto its back. Note: If your machine is stopping before draining, it will have water inside the tub which will drain out of the hole where the thermistor goes when you pull the old one out. It has an o-ring to seal it, so just expect a little water to come out and be ready to catch all the water or put the new one in quickly.

Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,

Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.

Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had

Very simple repair after watching YouTube video on how to complete repair.