Models
>
FH069FD7P
FH069FD7P (ABWEELC) LG Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for FH069FD7P
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$57.07
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it ...
In Stock
Order now and your part arrives by Mar 20
$34.97
The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with wat...
In Stock
Order now and your part arrives by Mar 20
$18.85
This magnetic door plunger is a genuine replacement component designed to keep the washing machine door slightly ajar when not in use. By allowing air circulation, it helps the inner door and tub seal...
In Stock
Order now and your part arrives by Mar 20
In Stock
Order now and your part arrives by Mar 20
$54.01
This hose has bellows to allow for flexibility during the wash and spin cycles.
In Stock
Order now and your part arrives by Mar 20
$24.10
This rubber tub seal fits between the front and rear halves of the washing machine’s outer tub to prevent water leaks. It helps maintain proper washing performance and may need replacement if you noti...
In Stock
Order now and your part arrives by Mar 20
$44.24
This tub bearing is for washers.
Tub bearing supports the spin basket shaft at the tub.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
In Stock
Order now and your part arrives by Mar 20
$126.95
This water inlet valve controls cold water flow for the bleach dispenser and prewash cycles. It has one standard hose inlet and three angled outlets—two to the right, one to the left. Designed for sel...
In Stock
Order now and your part arrives by Mar 20
Special Order
$24.10
This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your wa...
In Stock
Order now and your part arrives by Mar 20
$55.03
Tub bearing. This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly.
Special Order
In Stock
Order now and your part arrives by Mar 20
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for FH069FD7P
Viewing 14 of 14Will not drain
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
How to fix it
Engine runs but does not pump water
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jorge from Apple Valley, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam
... Read more
e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omnitech from Warrenville, IL
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door would not close
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replac
... Read more
e the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RALEIGH, NC
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
noisy operation, sometimes did not drain, gave OE code
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Was this instruction helpful to you?
Thank you for voting!