Models > WM3500CW

WM3500CW (01) LG Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$26.19
The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.
Special Order
Suspend the outer tub from the cabinet with this heavy-duty spring for select front-load washers and washer-dryer combinations. It carries the tub while absorbing movement through washing and spinning...
In Stock
Order now and your part arrives by Nov 22
In Stock
Order now and your part arrives by Nov 22
In Stock
Order now and your part arrives by Nov 22
$16.45
This hose clamp applies pressure around the hose end, holding it firmly against its fitting during operation. A secure hose connection helps keep water contained inside the appliance. This OEM part is...
In Stock
Order now and your part arrives by Nov 22
If your washer isn’t locking or starting like it should, this replacement door lock switch could be the fix you need. It helps your machine know when the door is closed so it can lock and begin the cy...
In Stock
Order now and your part arrives by Nov 22
This short washer shipping bolt assembly protects the wash tub during a move. It holds the suspended tub securely in place, limiting movement that could damage internal parts during transport. The bol...
In Stock
Order now and your part arrives by Nov 22
This thermistor sensor changes electrical resistance as temperature changes, sending a reading to the main control board so it can manage heat as needed. Accurate temperature feedback helps the applia...
In Stock
Order now and your part arrives by Nov 22
In Stock
Order now and your part arrives by Nov 22
This metal spring clamp assembly secures the rubber gasket to the tub, holding its edge in place as the tub moves during washing and spinning. Firm tension around the door boot helps keep wash water c...
In Stock
Order now and your part arrives by Nov 22
This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can...
Special Order
In Stock
Order now and your part arrives by Nov 22

Common Problems and Symptoms for WM3500CW

Viewing 6 of 6
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Locking Issues
Fixed by these parts
Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing
How to fix it
Water Filling Issues
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
CURTIS from OLIVE BRANCH, MS
Parts Used:
EBF61315802
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Washer did not recognize the door was shut
I removed the Wire and spring from the tub seal and then removed the seal on the side of the washer that contains the Door switch. I removed the two screws that held the door switch in place while holding the switch with my other hand. Once the screws where out I pulled the switch assembly out thru the gap and removed the wires from old assembly. I then plugged the wires into the new assembly aligned the holes up and put the screws back in the new door switch assembly. I then put the door seal and tub seal holder back on. This took about 15 minutes. I do recomend that you unplug the washer before starting this process.
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marcia from TROY, OH
Parts Used:
5221ER1003S
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Wrench (Adjustable)
Water inlet valve relacement
Installed correctly but PartsSelect sent WRONG part, but part number on bag was correct. Installation of WRONG part fried the main board. A $100 fix is now costing me about $1300.00 for technician service and new unit. I asked PartsSelect to help with cost since outcome is due to their error. Totally unsatisfied. Will not suggest company to other DIYers.
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tema from STATE ROAD, NC
Parts Used:
ACV72909506
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Washer drum extreme vibration when spinning
We replaced the three dampers, two in the front and one in the back. We referred to the YouTube video someone posted on this page.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!