Models
>
WM3670HVA01
WM3670HVA01 LG Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Models for WM3670HVA01
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
$59.43
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it ...
In Stock
Order now and your part arrives by Oct 26
$36.42
The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with wat...
In Stock
Order now and your part arrives by Oct 26
$25.10
If your washer isn’t dispensing detergent or fabric softener properly, this replacement container assembly may be the fix you need. Designed to hold liquid cleaning agents and release them at the righ...
In Stock
Order now and your part arrives by Oct 26
$137.30
This water inlet valve controls cold water flow for the bleach dispenser and prewash cycles. It has one standard hose inlet and three angled outlets—two to the right, one to the left. Designed for sel...
In Stock
Order now and your part arrives by Oct 26
$107.72
This flexible gasket seals the door on your LG or Kenmore front-load washer to keep water from leaking during cycles. If you’re seeing puddles, smelling mildew, or noticing moisture around the door, r...
In Stock
Order now and your part arrives by Oct 26
In Stock
Order now and your part arrives by Oct 26
$140.32
If your washer isn’t locking or starting like it should, this replacement door lock switch could be the fix you need. It helps your machine know when the door is closed so it can lock and begin the cy...
In Stock
Order now and your part arrives by Oct 26
In Stock
Order now and your part arrives by Oct 26
$57.30
This dispenser assembly holds and dispenses detergent and fabric softener during the wash cycle. Replace it if your current part is clogged, leaking, or damaged. Verify your washer model for proper fit before installing.
In Stock
Order now and your part arrives by Oct 26
$37.49
This part is the replacement fabric softener cap for your washer. It is also known as the washer dispenser drawer insert. It is made of blue plastic and is approximately 4-1/4 inches by 2-1/4 inches. ...
In Stock
Order now and your part arrives by Oct 26
In Stock
Order now and your part arrives by Oct 26
In Stock
Order now and your part arrives by Oct 26
Common Problems and Symptoms for WM3670HVA01
Viewing 15 of 15Will not drain
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Does not dispense fabric softener or detergent
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Engine runs but does not pump water
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jorge from Apple Valley, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam
... Read more
e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RALEIGH, NC
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
noisy operation, sometimes did not drain, gave OE code
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Northport, NY
- Parts Used:
- 5221ER1003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Inlet valve leak
Followed directions on the video and went like a charm. Very impressed with service and video
Was this instruction helpful to you?
Thank you for voting!