Models
>
WT7880HWA
WT7880HWA (ABWEUUS) LG Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WT7880HWA
Viewing 3 of 3Keep searches simple, eg. "belt" or "pump".
$49.45
Clothing moves over a covered mounting point with help from this washer pulsator cap. The round plastic cover snaps into the center of the washplate, concealing the mounting bolt and providing a smoot...
In Stock
Order now and your part arrives by Nov 24
$32.95
Restore a washer component?s fastening point with this replacement screw when the original is missing, stripped, or damaged. Secure fastening helps parts stay firmly attached during operation. A worn ...
In Stock
Order now and your part arrives by Nov 24
In Stock
Order now and your part arrives by Nov 24
This pressure sensor assembly measures changes in air pressure through a connected tube as water enters or leaves the tub. Accurate water level sensing helps the washer fill and advance through its cy...
In Stock
Order now and your part arrives by Nov 24
$154.80
This lid switch and lock assembly keeps the washer lid secure during operation. It detects whether the lid is closed and sends that information to the main control board. This is an OEM replacement ob...
In Stock
Order now and your part arrives by Nov 24
In Stock
Order now and your part arrives by Nov 24
$142.60
This washer inlet valve assembly is responsible for regulating the flow of both hot and cold water into your washing machine. It opens and closes at specific points during the wash cycle to ensure the...
In Stock
Order now and your part arrives by Nov 24
In Stock
Order now and your part arrives by Nov 24
On Order
In Stock
Order now and your part arrives by Nov 24
$139.19
This drain pump assembly is responsible for removing water from your washer during the drain cycle. It is typically at the bottom of the washing machine and connected to the drain hose. If it is damag...
In Stock
Order now and your part arrives by Nov 24
On Order
Common Problems and Symptoms for WT7880HWA
Viewing 10 of 10Leaking
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Does not dispense fabric softener or detergent
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Angelica from HOUSTON, TX
- Parts Used:
- 6323EL2001G
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Top loading washing machine displayed "tE" error
Disconnect machine from power source. Then, disconnect any tubes from the back side (make sure you close any water valves before doing so). Then, lay the machine on its back to access the bottom of the machine. Then, locate the thermistor and replace it with the new one (the thermistor will have two screws holding it in place, simply remo
... Read more
ve the screws and replace the thermistor, then screw it back in). After the new part is installed, stand the machine back up and make sure to connect any tubing to its proper place. Done.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from MANOR, TX
- Parts Used:
- 6323EL2001G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer was stopping during the spin cycle and making a grinding noise.
Our Samsung HE washer started making a grinding noise and stopping at the end of the rinse/spin cycle. I had replaced the clutch and seal 2 years ago and it sounded like it was going out again, however we were not getting the gunk inside the tub like before (seal) and the machine was throwing the tE error code when it stopped which it di
... Read more
d not do last time. According to the manual this meant a thermistor error and the solution was "Call for Service". The machine is 9 years old and way out of warranty so....uh No! I ordered the new thermistor for $15 plus shipping to correct the tE code before looking to replace the clutch again or get a new machine. The new thermistor arrived, leaned the machine on its back, unplug one connector, remove two screws and pull the old one out of it's hole, push the new one in, replace two screws and the connector and GO! Problem fixed! No tE code, no stopping, no grinding noise. As best I can tell, the old thermistor was faulting during the spin cycle and the machine went into emergency stop mode which made the grinding noise. It was not the clutch or bearing at all. Most of the repair time was moving the machine out and disconnecting lines so I could lean it onto its back. Note: If your machine is stopping before draining, it will have water inside the tub which will drain out of the hole where the thermistor goes when you pull the old one out. It has an o-ring to seal it, so just expect a little water to come out and be ready to catch all the water or put the new one in quickly.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas m from CARMICHAEL, CA
- Parts Used:
- 4263FA3933C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
leg broke off inside housing
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new
... Read more
leg was a breeze.
Read less
Was this instruction helpful to you?
Thank you for voting!